esphome/tests/test8.yaml

105 lines
1.6 KiB
YAML
Raw Normal View History

# Tests for ESP32-S3 boards
---
wifi:
ssid: "ssid"
network:
enable_ipv6: true
esp32:
board: esp32s3box
variant: ESP32S3
framework:
type: arduino
esphome:
2023-03-09 02:54:51 +01:00
name: esp32-s3-test
logger:
debug:
psram:
light:
- platform: neopixelbus
type: GRB
variant: WS2812
pin: GPIO38
num_leds: 1
id: neopixel
method: esp32_rmt
2023-03-09 02:54:51 +01:00
name: neopixel-enable
internal: false
restore_mode: ALWAYS_OFF
- platform: spi_led_strip
num_leds: 4
color_correct: [80%, 60%, 100%]
id: rgb_led
name: "RGB LED"
data_rate: 8MHz
spi:
Refactor SPI code; Add ESP-IDF hardware support (#5311) * Checkpoint * Checkpoint * Checkpoint * Revert hal change * Checkpoint * Checkpoint * Checkpoint * Checkpoint * ESP-IDF working * clang-format * use bus_list * Add spi_device; fix 16 bit transfer. * Enable multi_conf; Fix LSB 16 bit transactions * Formatting fixes * Clang-format, codeowners * Add test * Formatting * clang tidy * clang-format * clang-tidy * clang-format * Checkpoint * Checkpoint * Checkpoint * Revert hal change * Checkpoint * Checkpoint * Checkpoint * Checkpoint * ESP-IDF working * clang-format * use bus_list * Add spi_device; fix 16 bit transfer. * Enable multi_conf; Fix LSB 16 bit transactions * Formatting fixes * Clang-format, codeowners * Add test * Formatting * clang tidy * clang-format * clang-tidy * clang-format * Clang-tidy * Clang-format * clang-tidy * clang-tidy * Fix ESP8266 * RP2040 * RP2040 * Avoid use of spi1 as id * Refactor SPI code. Add support for ESP-IDF hardware SPI * Force SW only for RP2040 * Break up large transfers * Add interface: option for spi. validate pins in python. * Can't use match/case with Python 3.9. Check for inverted pins. * Work around target_platform issue with * Remove debug code * Optimize write_array16 * Show errors in hex * Only one spi on ESP32Cx variants * Ensure bus is claimed before asserting /CS. * Check on init/deinit * Allow maximum rate write only SPI on GPIO MUXed pins. * Clang-format * Clang-tidy * Fix issue with reads. * Finger trouble... * Make comment about missing SPI on Cx variants * Pacify CI clang-format. Did not complain locally?? * Restore 8266 to its former SPI glory * Fix per clang-format * Move validation and choice of SPI into Python code. * Add test for interface: config * Fix issues found on self-review. --------- Co-authored-by: Keith Burzinski <kbx81x@gmail.com>
2023-09-08 09:27:19 +02:00
id: spi_id_1
clk_pin: GPIO7
mosi_pin: GPIO6
Refactor SPI code; Add ESP-IDF hardware support (#5311) * Checkpoint * Checkpoint * Checkpoint * Revert hal change * Checkpoint * Checkpoint * Checkpoint * Checkpoint * ESP-IDF working * clang-format * use bus_list * Add spi_device; fix 16 bit transfer. * Enable multi_conf; Fix LSB 16 bit transactions * Formatting fixes * Clang-format, codeowners * Add test * Formatting * clang tidy * clang-format * clang-tidy * clang-format * Checkpoint * Checkpoint * Checkpoint * Revert hal change * Checkpoint * Checkpoint * Checkpoint * Checkpoint * ESP-IDF working * clang-format * use bus_list * Add spi_device; fix 16 bit transfer. * Enable multi_conf; Fix LSB 16 bit transactions * Formatting fixes * Clang-format, codeowners * Add test * Formatting * clang tidy * clang-format * clang-tidy * clang-format * Clang-tidy * Clang-format * clang-tidy * clang-tidy * Fix ESP8266 * RP2040 * RP2040 * Avoid use of spi1 as id * Refactor SPI code. Add support for ESP-IDF hardware SPI * Force SW only for RP2040 * Break up large transfers * Add interface: option for spi. validate pins in python. * Can't use match/case with Python 3.9. Check for inverted pins. * Work around target_platform issue with * Remove debug code * Optimize write_array16 * Show errors in hex * Only one spi on ESP32Cx variants * Ensure bus is claimed before asserting /CS. * Check on init/deinit * Allow maximum rate write only SPI on GPIO MUXed pins. * Clang-format * Clang-tidy * Fix issue with reads. * Finger trouble... * Make comment about missing SPI on Cx variants * Pacify CI clang-format. Did not complain locally?? * Restore 8266 to its former SPI glory * Fix per clang-format * Move validation and choice of SPI into Python code. * Add test for interface: config * Fix issues found on self-review. --------- Co-authored-by: Keith Burzinski <kbx81x@gmail.com>
2023-09-08 09:27:19 +02:00
interface: any
spi_device:
id: spidev
data_rate: 2MHz
spi_id: spi_id_1
mode: 3
bit_order: lsb_first
display:
- platform: ili9xxx
id: displ8
model: ili9342
cs_pin: GPIO5
dc_pin: GPIO4
reset_pin:
number: GPIO48
allow_other_uses: true
i2c:
scl: GPIO18
sda: GPIO8
touchscreen:
- platform: tt21100
display: displ8
interrupt_pin:
number: GPIO3
ignore_strapping_warning: true
allow_other_uses: false
reset_pin:
number: GPIO48
allow_other_uses: true
binary_sensor:
- platform: tt21100
name: Home Button
index: 1
sensor:
- platform: debug
free:
name: "Heap Free"
block:
name: "Max Block Free"
loop_time:
name: "Loop Time"
psram:
name: "PSRAM Free"
# Purposely test that `animation:` does auto-load `image:`
# Keep the `image:` undefined.
# image:
animation:
- id: rgb565_animation
file: pnglogo.png
type: RGB565
2024-02-21 05:14:30 +01:00
use_transparency: false