esphome/tests/test2.yaml
2023-12-05 08:56:53 +09:00

869 lines
21 KiB
YAML

---
esphome:
name: $devicename
platform: ESP32
board: nodemcu-32s
build_path: build/test2
globals:
- id: my_global_string
type: std::string
restore_value: yes
max_restore_data_length: 70
initial_value: '"DefaultValue"'
substitutions:
devicename: test2
ethernet:
type: LAN8720
mdc_pin:
allow_other_uses: true
number: GPIO23
mdio_pin:
allow_other_uses: true
number: GPIO25
clk_mode: GPIO0_IN
phy_addr: 0
power_pin:
allow_other_uses: true
number: GPIO25
manual_ip:
static_ip: 192.168.178.56
gateway: 192.168.178.1
subnet: 255.255.255.0
domain: .local
network:
enable_ipv6: true
mdns:
disabled: true
api:
i2c:
sda:
allow_other_uses: true
number: 21
scl:
allow_other_uses: true
number: 22
scan: false
spi:
clk_pin:
allow_other_uses: true
number: GPIO21
mosi_pin:
allow_other_uses: true
number: GPIO22
miso_pin:
allow_other_uses: true
number: GPIO23
uart:
tx_pin:
allow_other_uses: true
number: GPIO22
rx_pin:
allow_other_uses: true
number: GPIO23
baud_rate: 115200
# Specifically added for testing debug with no after: definition.
debug:
dummy_receiver: false
direction: rx
sequence:
- lambda: UARTDebug::log_hex(direction, bytes, ':');
ota:
safe_mode: true
port: 3286
num_attempts: 15
logger:
level: DEBUG
debug:
deep_sleep:
run_duration:
default: 20s
gpio_wakeup_reason: 10s
touch_wakeup_reason: 15s
sleep_duration: 50s
wakeup_pin:
allow_other_uses: true
number: GPIO2
wakeup_pin_mode: INVERT_WAKEUP
as3935_i2c:
irq_pin:
allow_other_uses: true
number: GPIO12
mcp3008:
- id: mcp3008_hub
cs_pin:
allow_other_uses: true
number: GPIO12
output:
- platform: ac_dimmer
id: dimmer1
gate_pin: GPIO5
zero_cross_pin:
allow_other_uses: true
number: GPIO12
sensor:
- platform: homeassistant
entity_id: sensor.hello_world
id: ha_hello_world
- platform: homeassistant
entity_id: climate.living_room
attribute: temperature
id: ha_hello_world_temperature
- platform: ble_rssi
mac_address: AC:37:43:77:5F:4C
name: BLE Google Home Mini RSSI value
- platform: ble_rssi
service_uuid: 11aa
name: BLE Test Service 16
- platform: ble_rssi
service_uuid: "11223344"
name: BLE Test Service 32
- platform: ble_rssi
service_uuid: 11223344-5566-7788-99aa-bbccddeeff00
name: BLE Test Service 128
- platform: ble_rssi
service_uuid: 11223344-5566-7788-99aa-bbccddeeff00
name: BLE Test iBeacon UUID
- platform: b_parasite
mac_address: F0:CA:F0:CA:01:01
humidity:
name: b-parasite Air Humidity
temperature:
name: b-parasite Air Temperature
moisture:
name: b-parasite Soil Moisture
battery_voltage:
name: b-parasite Battery Voltage
illuminance:
name: b-parasite Illuminance
- platform: senseair
id: senseair0
co2:
name: SenseAir CO2 Value
on_value:
then:
- senseair.background_calibration: senseair0
- senseair.background_calibration_result: senseair0
- senseair.abc_get_period: senseair0
- senseair.abc_enable: senseair0
- senseair.abc_disable: senseair0
update_interval: 15s
- platform: ruuvitag
mac_address: FF:56:D3:2F:7D:E8
humidity:
name: RuuviTag Humidity
temperature:
name: RuuviTag Temperature
pressure:
name: RuuviTag Pressure
acceleration_x:
name: RuuviTag Acceleration X
acceleration_y:
name: RuuviTag Acceleration Y
acceleration_z:
name: RuuviTag Acceleration Z
battery_voltage:
name: RuuviTag Battery Voltage
tx_power:
name: RuuviTag TX Power
movement_counter:
name: RuuviTag Movement Counter
measurement_sequence_number:
name: RuuviTag Measurement Sequence Number
- platform: as3935
lightning_energy:
name: Lightning Energy
distance:
name: Distance Storm
- platform: xiaomi_hhccjcy01
mac_address: 94:2B:FF:5C:91:61
temperature:
name: Xiaomi HHCCJCY01 Temperature
moisture:
name: Xiaomi HHCCJCY01 Moisture
illuminance:
name: Xiaomi HHCCJCY01 Illuminance
conductivity:
name: Xiaomi HHCCJCY01 Soil Conductivity
battery_level:
name: Xiaomi HHCCJCY01 Battery Level
- platform: xiaomi_lywsdcgq
mac_address: 7A:80:8E:19:36:BA
temperature:
name: Xiaomi LYWSDCGQ Temperature
humidity:
name: Xiaomi LYWSDCGQ Humidity
battery_level:
name: Xiaomi LYWSDCGQ Battery Level
- platform: xiaomi_lywsd02
mac_address: 3F:5B:7D:82:58:4E
temperature:
name: Xiaomi LYWSD02 Temperature
humidity:
name: Xiaomi LYWSD02 Humidity
battery_level:
name: Xiaomi LYWSD02 Battery Level
- platform: xiaomi_cgg1
mac_address: 7A:80:8E:19:36:BA
temperature:
name: Xiaomi CGG1 Temperature
humidity:
name: Xiaomi CGG1 Humidity
battery_level:
name: Xiaomi CGG1 Battery Level
- platform: xiaomi_gcls002
mac_address: 94:2B:FF:5C:91:61
temperature:
name: GCLS02 Temperature
moisture:
name: GCLS02 Moisture
conductivity:
name: GCLS02 Soil Conductivity
illuminance:
name: GCLS02 Illuminance
- platform: xiaomi_hhccpot002
mac_address: 94:2B:FF:5C:91:61
moisture:
name: HHCCPOT002 Moisture
conductivity:
name: HHCCPOT002 Soil Conductivity
- platform: xiaomi_lywsd03mmc
mac_address: A4:C1:38:4E:16:78
bindkey: e9efaa6873f9f9c87a5e75a5f814801c
temperature:
name: Xiaomi LYWSD03MMC Temperature
humidity:
name: Xiaomi LYWSD03MMC Humidity
battery_level:
name: Xiaomi LYWSD03MMC Battery Level
- platform: xiaomi_cgd1
mac_address: A4:C1:38:D1:61:7D
bindkey: c99d2313182473b38001086febf781bd
temperature:
name: Xiaomi CGD1 Temperature
humidity:
name: Xiaomi CGD1 Humidity
battery_level:
name: Xiaomi CGD1 Battery Level
- platform: xiaomi_jqjcy01ym
mac_address: 7A:80:8E:19:36:BA
temperature:
name: JQJCY01YM Temperature
humidity:
name: JQJCY01YM Humidity
formaldehyde:
name: JQJCY01YM Formaldehyde
battery_level:
name: JQJCY01YM Battery Level
- platform: xiaomi_mhoc303
mac_address: E7:50:59:32:A0:1C
temperature:
name: MHO-C303 Temperature
humidity:
name: MHO-C303 Humidity
battery_level:
name: MHO-C303 Battery Level
- platform: atc_mithermometer
mac_address: A4:C1:38:4E:16:78
temperature:
name: ATC Temperature
humidity:
name: ATC Humidity
battery_level:
name: ATC Battery-Level
battery_voltage:
name: ATC Battery-Voltage
- platform: pvvx_mithermometer
mac_address: A4:C1:38:4E:16:78
temperature:
name: PVVX Temperature
humidity:
name: PVVX Humidity
battery_level:
name: PVVX Battery-Level
battery_voltage:
name: PVVX Battery-Voltage
- platform: inkbird_ibsth1_mini
mac_address: 38:81:D7:0A:9C:11
temperature:
name: Inkbird IBS-TH1 Temperature
humidity:
name: Inkbird IBS-TH1 Humidity
battery_level:
name: Inkbird IBS-TH1 Battery Level
- platform: xiaomi_rtcgq02lm
id: motion_rtcgq02lm
battery_level:
name: Mi Motion Sensor 2 Battery level
- platform: ltr390
uv:
name: LTR390 UV
uv_index:
name: LTR390 UVI
light:
name: LTR390 Light
ambient_light:
name: LTR390 ALS
gain: X3
resolution: 18
window_correction_factor: 1.0
address: 0x53
update_interval: 60s
- platform: sgp4x
voc:
name: VOC Index
id: sgp40_voc_index
algorithm_tuning:
index_offset: 100
learning_time_offset_hours: 12
learning_time_gain_hours: 12
gating_max_duration_minutes: 180
std_initial: 50
gain_factor: 230
nox:
name: NOx
algorithm_tuning:
index_offset: 100
learning_time_offset_hours: 12
learning_time_gain_hours: 12
gating_max_duration_minutes: 180
std_initial: 50
gain_factor: 230
update_interval: 5s
- platform: mcp3008
update_interval: 5s
mcp3008_id: mcp3008_hub
id: freezer_temp_source
reference_voltage: 3.19
number: 0
- id: airthingswp
platform: airthings_wave_plus
ble_client_id: airthings01
update_interval: 5min
battery_update_interval: 12h
temperature:
name: Wave Plus Temperature
radon:
name: Wave Plus Radon
radon_long_term:
name: Wave Plus Radon Long Term
pressure:
name: Wave Plus Pressure
humidity:
name: Wave Plus Humidity
co2:
name: Wave Plus CO2
tvoc:
name: Wave Plus VOC
battery_voltage:
name: Wave Plus Battery Voltage
- id: airthingswm
platform: airthings_wave_mini
ble_client_id: airthingsmini01
update_interval: 5min
battery_update_interval: 12h
temperature:
name: Wave Mini Temperature
humidity:
name: Wave Mini Humidity
pressure:
name: Wave Mini Pressure
tvoc:
name: Wave Mini VOC
battery_voltage:
name: Wave Mini Battery Voltage
- platform: ina260
address: 0x40
current:
name: INA260 Current
power:
name: INA260 Power
bus_voltage:
name: INA260 Voltage
update_interval: 60s
- platform: radon_eye_rd200
ble_client_id: radon_eye_ble_id
update_interval: 10min
radon:
name: RD200 Radon
radon_long_term:
name: RD200 Radon Long Term
- platform: mopeka_pro_check
mac_address: D3:75:F2:DC:16:91
tank_type: CUSTOM
custom_distance_full: 40cm
custom_distance_empty: 10mm
temperature:
name: Propane test temp
level:
name: Propane test level
distance:
name: Propane test distance
battery_level:
name: Propane test battery level
- platform: ufire_ec
id: ufire_ec_board
ec:
name: Ufire EC
temperature_sensor: ha_hello_world_temperature
temperature_compensation: 20.0
temperature_coefficient: 0.019
- platform: ufire_ise
id: ufire_ise_board
temperature_sensor: ha_hello_world_temperature
ph:
name: Ufire pH
- platform: mics_4514
update_interval: 60s
nitrogen_dioxide:
name: MICS-4514 NO2
carbon_monoxide:
name: MICS-4514 CO
methane:
name: MICS-4514 CH4
hydrogen:
name: MICS-4514 H2
ethanol:
name: MICS-4514 C2H5OH
ammonia:
name: MICS-4514 NH3
- platform: mopeka_std_check
mac_address: D3:75:F2:DC:16:91
tank_type: CUSTOM
custom_distance_full: 40cm
custom_distance_empty: 10mm
temperature:
name: Propane test temp
level:
name: Propane test level
distance:
name: Propane test distance
battery_level:
name: Propane test battery level
- platform: duty_time
id: duty_time1
name: Test Duty Time
restore: true
last_time:
name: Test Last Duty Time Sensor
sensor: ha_hello_world_binary
- platform: duty_time
id: duty_time2
name: Test Duty Time 2
restore: false
lambda: "return true;"
time:
- platform: homeassistant
on_time:
- at: "16:00:00"
then:
- logger.log: It's 16:00
- if:
condition:
- sensor.duty_time.is_running: duty_time2
then:
- sensor.duty_time.start: duty_time1
- if:
condition:
- sensor.duty_time.is_not_running: duty_time1
then:
- sensor.duty_time.stop: duty_time2
- sensor.duty_time.reset: duty_time1
esp32_touch:
setup_mode: true
binary_sensor:
- platform: homeassistant
entity_id: binary_sensor.hello_world
id: ha_hello_world_binary
- platform: homeassistant
entity_id: binary_sensor.hello
attribute: world
id: ha_hello_world_binary_attribute
- platform: ble_presence
mac_address: AC:37:43:77:5F:4C
name: ESP32 BLE Tracker Google Home Mini
- platform: ble_presence
service_uuid: 11aa
name: BLE Test Service 16 Presence
- platform: ble_presence
service_uuid: "11223344"
name: BLE Test Service 32 Presence
- platform: ble_presence
service_uuid: 11223344-5566-7788-99aa-bbccddeeff00
name: BLE Test Service 128 Presence
- platform: ble_presence
ibeacon_uuid: 11223344-5566-7788-99aa-bbccddeeff00
ibeacon_major: 100
ibeacon_minor: 1
name: BLE Test iBeacon Presence
- platform: esp32_touch
name: ESP32 Touch Pad GPIO27
pin: GPIO27
threshold: 1000
- platform: as3935
name: Storm Alert
- platform: xiaomi_mue4094rt
name: MUE4094RT Motion
mac_address: 7A:80:8E:19:36:BA
timeout: 5s
- platform: xiaomi_mjyd02yla
name: MJYD02YL-A Motion
mac_address: 50:EC:50:CD:32:02
bindkey: 48403ebe2d385db8d0c187f81e62cb64
idle_time:
name: MJYD02YL-A Idle Time
light:
name: MJYD02YL-A Light Status
battery_level:
name: MJYD02YL-A Battery Level
- platform: xiaomi_wx08zm
name: WX08ZM Activation State
mac_address: 74:a3:4a:b5:07:34
tablet:
name: WX08ZM Tablet Resource
battery_level:
name: WX08ZM Battery Level
- platform: xiaomi_cgpr1
name: CGPR1 Motion
mac_address: "12:34:56:12:34:56"
bindkey: 48403ebe2d385db8d0c187f81e62cb64
battery_level:
name: CGPR1 battery Level
idle_time:
name: CGPR1 Idle Time
illuminance:
name: CGPR1 Illuminance
- platform: xiaomi_rtcgq02lm
id: motion_rtcgq02lm
motion:
name: Mi Motion Sensor 2
light:
name: Mi Motion Sensor 2 Light
button:
name: Mi Motion Sensor 2 Button
- platform: gpio
id: gpio_set_retry_test
pin:
allow_other_uses: true
number: GPIO9
on_press:
then:
- lambda: |-
App.scheduler.set_retry(id(gpio_set_retry_test), "set_retry_test", 100, 3, [](const uint8_t remaining) {
return remaining ? RetryResult::RETRY : RetryResult::DONE; // just to reference both symbols
}, 5.0f);
esp32_ble_tracker:
on_ble_advertise:
- mac_address:
- AA:BB:CC:DD:EE:FF
- FF:EE:DD:CC:BB:AA
then:
# yamllint disable rule:line-length
- lambda: !lambda |-
ESP_LOGD("main", "The device address (%s) exists in list", x.address_str().c_str());
# yamllint enable rule:line-length
- mac_address: AC:37:43:77:5F:4C
then:
# yamllint disable rule:line-length
- lambda: !lambda |-
ESP_LOGD("main", "The device address is %s", x.address_str().c_str());
# yamllint enable rule:line-length
- then:
# yamllint disable rule:line-length
- lambda: !lambda |-
ESP_LOGD("main", "The device address is %s", x.address_str().c_str());
# yamllint enable rule:line-length
on_ble_service_data_advertise:
- service_uuid: ABCD
then:
- lambda: !lambda |-
ESP_LOGD("main", "Length of service data is %i", x.size());
on_ble_manufacturer_data_advertise:
- manufacturer_id: ABCD
then:
- lambda: !lambda |-
ESP_LOGD("main", "Length of manufacturer data is %i", x.size());
ble_client:
- mac_address: 01:02:03:04:05:06
id: airthings01
- mac_address: 01:02:03:04:05:06
id: airthingsmini01
- mac_address: 01:02:03:04:05:06
id: radon_eye_ble_id
airthings_ble:
radon_eye_ble:
ruuvi_ble:
xiaomi_ble:
mopeka_ble:
bluetooth_proxy:
active: true
xiaomi_rtcgq02lm:
- id: motion_rtcgq02lm
mac_address: 01:02:03:04:05:06
bindkey: "48403ebe2d385db8d0c187f81e62cb64"
status_led:
pin:
allow_other_uses: true
number: GPIO2
text_sensor:
- platform: version
name: ESPHome Version
icon: mdi:icon
id: version_sensor
on_value:
- if:
condition:
- api.connected:
then:
# yamllint disable rule:line-length
- lambda: !lambda |-
ESP_LOGD("main", "The state is %s=%s", x.c_str(), id(version_sensor).state.c_str());
# yamllint enable rule:line-length
- script.execute: my_script
- script.execute:
id: my_script_with_params
prefix: Running my_script_with_params
param2: 100
param3: true
- script.execute:
id: my_script_with_params
prefix: Running my_script_with_params using lambda parameters
param2: !lambda return 200;
param3: !lambda return true;
- homeassistant.service:
service: notify.html5
data:
title: New Humidity
data_template:
message: The humidity is {{ my_variable }}%.
variables:
my_variable: |-
return id(version_sensor).state;
my_variable_str: |-
return "Hello World";
- homeassistant.service:
service: light.turn_on
data:
entity_id: light.my_light
- homeassistant.tag_scanned:
tag: 1234-abcd
- homeassistant.tag_scanned: 1234-abcd
- deep_sleep.enter:
sleep_duration: 30min
- deep_sleep.enter:
sleep_duration: !lambda "return 30 * 60 * 1000;"
- platform: template
name: Template Text Sensor
lambda: |-
return {"Hello World"};
filters:
- to_upper:
- to_lower:
- append: xyz
- prepend: abcd
- substitute:
- Hello -> Goodbye
- map:
- red -> green
- lambda: 'return {"1234"};'
- platform: homeassistant
entity_id: sensor.hello_world2
id: ha_hello_world2
- platform: homeassistant
entity_id: sensor.hello_world3
id: ha_hello_world3
attribute: some_attribute
- platform: ble_scanner
name: Scanner
script:
- id: my_script
mode: single
then:
- lambda: 'ESP_LOGD("main", "Hello World!");'
- id: my_script_queued
mode: queued
max_runs: 2
then:
- lambda: 'ESP_LOGD("main", "Hello World!");'
- id: my_script_parallel
mode: parallel
max_runs: 2
then:
- lambda: 'ESP_LOGD("main", "Hello World!");'
- id: my_script_restart
mode: restart
then:
- lambda: 'ESP_LOGD("main", "Hello World!");'
- id: my_script_with_params
parameters:
prefix: string
param2: int
param3: bool
then:
- lambda: 'ESP_LOGD("main", (prefix + " Hello World!" + to_string(param2) + " " + to_string(param3)).c_str());'
stepper:
- platform: uln2003
id: my_stepper
pin_a:
allow_other_uses: true
number: GPIO23
pin_b: GPIO27
pin_c:
allow_other_uses: true
number: GPIO25
pin_d: GPIO26
sleep_when_done: false
step_mode: HALF_STEP
max_speed: 250 steps/s
# Optional:
acceleration: inf
deceleration: inf
interval:
interval: 5s
startup_delay: 10s
then:
- logger.log: Interval Run
display:
- platform: st7789v
model: LILYGO_T-EMBED_170X320
spi_mode: mode0
height: 320
width: 170
offset_height: 35
offset_width: 0
dc_pin: GPIO13
reset_pin:
allow_other_uses: true
number: GPIO9
image:
- id: binary_image
file: pnglogo.png
type: BINARY
dither: FloydSteinberg
- id: transparent_transparent_image
file: pnglogo.png
type: TRANSPARENT_BINARY
- id: rgba_image
file: pnglogo.png
type: RGBA
resize: 50x50
- id: rgb24_image
file: pnglogo.png
type: RGB24
use_transparency: yes
- id: rgb565_image
file: pnglogo.png
type: RGB565
use_transparency: no
- id: web_svg_image
file: https://raw.githubusercontent.com/esphome/esphome-docs/a62d7ab193c1a464ed791670170c7d518189109b/images/logo.svg
resize: 256x48
type: TRANSPARENT_BINARY
- id: web_tiff_image
file: https://upload.wikimedia.org/wikipedia/commons/b/b6/SIPI_Jelly_Beans_4.1.07.tiff
type: RGB24
resize: 48x48
- id: web_redirect_image
file: https://avatars.githubusercontent.com/u/3060199?s=48&v=4
type: RGB24
resize: 48x48
- id: mdi_alert
file: mdi:alert-circle-outline
resize: 50x50
- id: another_alert_icon
file: mdi:alert-outline
type: BINARY
font:
- file: "gfonts://Roboto"
id: roboto
size: 20
graph:
- id: my_graph
sensor: ha_hello_world_temperature
duration: 1h
width: 100
height: 100
cap1188:
id: cap1188_component
address: 0x29
touch_threshold: 0x20
allow_multiple_touches: true
reset_pin: 14
switch:
- platform: template
name: Test BLE Write Action
turn_on_action:
- ble_client.ble_write:
id: airthings01
service_uuid: F61E3BE9-2826-A81B-970A-4D4DECFABBAE
characteristic_uuid: 6490FAFE-0734-732C-8705-91B653A081FC
value: [0x01, 0xab, 0xff]
- ble_client.ble_write:
id: airthings01
service_uuid: F61E3BE9-2826-A81B-970A-4D4DECFABBAE
characteristic_uuid: 6490FAFE-0734-732C-8705-91B653A081FC
value: !lambda |-
return {0x13, 0x37};
esp32_ble_server:
id: ble
manufacturer_data: [0x72, 0x4, 0x00, 0x23]
text:
- platform: template
name: My Text
id: my_text
min_length: 0
max_length: 20
mode: text
pattern: "[a-z]+"
optimistic: true
restore_value: true
initial_value: "Hello World"
- platform: copy
name: My Text Copy
id: my_text_copy
source_id: my_text
mode: password