# Setting up Brocade FCX & ICX6610 **Note:** This page is for the FCX & ICX6610. If you have a different model, choose it from the lefthand menu. ## Updating The Software Download the ZIP below, which contains the firmware files and documentation you'll need. [```Brocade v8030 Firmware/Docu Zip```](http://fohdeesha.com/data/other/brocade/8030sa.zip) ```SW version: 08030sa``` ```ZIP Updated: 11-03-2018``` ```MD5: 0c02f16a73f75ffd0d30d4cb0085cad0``` **Connect** to the switches serial/console port using a program like Putty (9600 8N1), and connect the dedicated management port to your network (do not use a "normal" port). You need to set up a temporary TFTP server - I recommend [Tftpd32 Portable Edition](http://www.tftpd64.com/tftpd32_download.html) if you're on Windows and don't want to install anything. Point the server to an empty folder to serve files from. From the ZIP, copy the bootloader from the ```Boot``` folder into your tftp server directory. Then, from the ```Images``` folder, copy over the OS image to the same place. If you have a PoE model, copy over the PoE firmware from the `PoE Firmware` folder to your TFTP directory as well. Power on the switch while watching your serial terminal - it will have a prompt saying ```Hit b to enter the boot monitor``` - press ```b``` quickly and you'll be dropped into the bootloader prompt, now we can upgrade the software. If you missed the prompt and it boots the OS instead, pull power and try again. At the boot prompt, we need to give it a temporary IP in the subnet of your network, so it can talk to your TFTP server. This IP will not be used again after it leaves the bootloader. Replace the IP in the example below with an unused IP on your subnet: ``` ip address 192.168.1.50/24 ``` Now we can update the bootloader. Replace the IP with the IP of your tftp server, and replace the filename with the name of the file you copied out of the boot folder if it differs: ``` copy tftp flash 192.168.1.49 grz10100.bin boot ``` After a few seconds it should finish, then we can flash the main OS. Replace the IP with the IP of your tftp server, and change the filename to match if necessary: ``` copy tftp flash 192.168.1.49 FCXR08030sa.bin primary ``` It will take a little longer. When it finishes, we need to erase the current config & any passwords, then tell the switch to reboot into the full OS: ``` factory set-default reset ``` ## Initial Configuration Now that it's booted into the full OS you may get ***TFTP timed out*** errors in the console, this is normal. We'll fix that in the next section. Check that the version matches what you just flashed: ``` show version ``` Towards the top of the output, it should say ```SW: Version XX.X.XXX``` - it should be the v8 version you flashed. Now to make any changes we must enter the enable level: ``` enable ``` To make configuration changes, we must then enter the configure CLI level: ``` configure terminal ``` Now tell it to generate an RSA keypair - this enables SSH access: ``` crypto key generate rsa ``` ## Configuring Network Details First we need to disable DHCP so it doesn't automatically grab an address and attempt to load a config via tftp, then reload so it takes effect: ``` ip dhcp-client disable write memory exit reload ``` Once the switch comes back up, enter the configure terminal level and give the switch a friendly name: ``` enable configure terminal hostname intertubes ``` We need to give the switch an IP. By default, all ports are in VLAN 1, so it will behave like a typical switch. First we need to give VLAN 1 its own virtual interface: ``` vlan 1 router-interface ve 1 exit ``` Now we need to assign that virtual interface an address. Choose an IP that is unused in your subnet, and out of your DHCP server range (ping it first to be sure it's unused): ``` interface ve 1 ip address 192.168.1.2/24 exit ``` The switch now has an IP. **Unplug your ethernet cable from the isolated management port, and plug it into any of the normal ports on the front.** You can now telnet to it and no longer need serial access. It also supports SSH access, but you need to follow the rest of the guide first. ## Update PoE Firmware If your switch is the PoE model, you need to update the PoE controller firmware. If it's a non-PoE model, skip this step. Assuming you completed the previous section and the switch now has in-band network access, just do the following: ``` exit inline power install-firmware stack-unit 1 tftp 192.168.1.8 fcx_poeplus_02.1.0.b004.fw #after a few seconds, hit enter to return to cli #save changes you made from the previous section write memory #reload the switch reload #you'll probably get a message that it hasn't finished. it can take up to 10 minutes #run "show log" occasionally to monitor the update progress #try the "reload" command again once it's reached 100% #once you've rebooted back into the OS: enable configure terminal ``` Now you have the latest PoE firmware, and can continue on. ## If Access Protection Is NOT Required If you do **not** want to password protect access to the switch (you're using it in a lab), follow this section. If you'd like to password protect it, skip to the next section. Allow SSH login with no passwords configured: ``` ip ssh permit-empty-passwd yes ``` ## If Access Protection IS Required (or WEB-UI Access) If you do want to secure access to the switch, or use the (limited) web UI, follow this section. If not, skip it. To secure the switch, we need to create an account - "root" can be any username string you wish: ``` username root password yourpasshere ``` We also need to tell it to use our new local user account(s) to authorize attempts to log in, use the webpage, as well as attempts to enter the ```enable``` CLI level: ``` aaa authentication login default local aaa authentication enable default local aaa authentication web default local ``` If you wanted to use the WEB UI, you can now log into it using the credentials you created above. You should enable authentication for telnet access as well: ``` enable telnet authentication ``` If your switch is outside of your home, or accessible by others in any way, telnet should be disabled entirely, and access to the serial console should also be password protected. Otherwise skip this step at your discretion: ``` no telnet server enable aaa console ``` ### OPTIONAL: Key Based SSH Access If you have followed the above to set up authentication, and also wish to disable password-based SSH login and set up a key pair instead, follow this section. If not, skip it. Enable key login, and disable password login: ``` ip ssh key-authentication yes ip ssh password-authentication no ``` Now we have to generate our key pair with [puttygen](https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html) on windows or ```ssh-keygen -t rsa``` on linux. The default settings of RSA @ 2048 bits works without issue. Generate the pair and save out both the public and private key. Copy the public key file to your TFTP server. Then use the following command to import it into your switch: ``` ip ssh pub-key-file tftp 192.168.1.49 public.key ``` You shouldn't need to be told basic key management if you're following this section, but just in case - copy your private key to the proper location on the *nix machine you'll be SSH'ing from, or if you're on windows, load it using [pageant](https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html). Now when you SSH to the switch, it will authenticate using your private key. ## Saving & Conclusions Whenever you make changes (like above) they take effect immediately, however they are not saved to onboard flash. So if you reboot the switch, they will be lost. To permanently save them to onboard flash, use the following command: ``` write memory ``` Your switch now has a basic configuration, as well as an IP address you can telnet or SSH to for further configuration. Some more useful general commands: Show chassis information like fan and temperature status: ``` show chassis ``` Show a table of all interfaces: ``` show interface brief ``` To show one interface in detail: ``` show interfaces ethernet 1/1/1 #Also works for virtual interfaces: show interfaces ve 1 ``` Give a port a friendly name: ``` interface ethernet 1/1/1 port-name freenas show interfaces brief ethernet 1/1/1 exit ``` Show the running configuration: ``` show run ``` Show the system log: ``` show log ``` To remove configuration options, put a ```no``` in front of them at the appropriate CLI level: ``` no hostname intertubes ``` ## Tips To exit the CLI level you are at, use `exit`. So assuming you are still at the ```configure terminal``` level, type the following to exit back to the ```enable``` level: ``` exit ``` Commands can also be shortened, as long as they are still unique. So to re-enter the configure terminal level, Instead of typing the entirety of ```configure terminal```, the following will also work: ``` conf t ``` There is also tab help and completion. To see all the commands available at the current CLI level, just hit tab. To see the options available for a certain command, just type that command (like ```ip```) then hit tab a couple times. ## Advanced Configuration ### Default Route & DNS To give the switch a default route and a DNS server so it can reach external hostnames and IP's (to ping external servers or to update time via NTP etc), do the following. replace the IP with the IP of your gateway/router/etc. Assuming you are still at the ```configure terminal``` level: ``` ip dns server-address 192.168.1.1 ip route 0.0.0.0/0 192.168.1.1 ``` ### NTP To have the switch keep its time synced via NTP (so its logs make more sense), use the following. If you live in an area that doesn't use Daylight Savings, skip the ```clock summer-time``` command. Use tab completion for the timezone command to see what's available. The IP's in the following example are google's NTP servers and work well for most cases: ``` clock summer-time clock timezone gmt GMT-05 ntp disable serve server 216.239.35.0 server 216.239.35.4 exit ``` ### SNMP To quickly enable SNMPv2 (read only), follow the below. SNMP v3 is available but you'll have to refer to the included documentation: ``` snmp-server community public ro ``` ### Saving If you made any of the above extra changes, remember they have not been saved to onboard flash yet. Do so: ``` write memory ``` ## SFP/Optics Information Brocade does not restrict the use of optics by manufacturer, they'll take anything given it's the right protocol. However optical monitoring information is disabled unless it sees Brocade or Foundry optics. So if you want to see information like this : ``` telnet@Route2(config)#sh optic 5 Port Temperature Tx Power Rx Power Tx Bias Current +----+-----------+--------------+--------------+---------------+ 5 32.7460 C -002.6688 dBm -002.8091 dBm 5.472 mA Normal Normal Normal Normal ``` You'll need to pick up some official Brocade or Foundry optics on ebay, or buy some flashed optics from FiberStore. ### Thanks: [**Fohdeesha**](http://fohdeesha.com/) ### Contributing: The markdown source for these guides is hosted on [**my Github repo.**](https://github.com/Fohdeesha/lab-docu) If you have any suggested changes or additions feel free to submit a pull request. ```Documentation version:``` [ v1.5 (11-04-18)](https://github.com/Fohdeesha/lab-docu/commits/master)