mirror of
https://github.com/esphome/esphome-docs.git
synced 2024-09-06 00:58:07 +02:00
339 lines
9.8 KiB
ReStructuredText
339 lines
9.8 KiB
ReStructuredText
RF Bridge Component
|
|
===================
|
|
|
|
.. seo::
|
|
:description: Instructions for setting up the RF Bridge in ESPHome.
|
|
:image: rf_bridge.jpg
|
|
:keywords: RF Bridge
|
|
|
|
The ``RF Bridge`` Component provides the ability to send and receive 433MHz remote codes without hardware
|
|
hacking the circuit board to bypass the ``efm8bb1`` MCU. This component implements the communcation protocol
|
|
that the original ``efm8bb1`` firmware implements. The device is connected via the
|
|
:doc:`UART bus </components/uart>`. The uart bus must be configured at the same speed of the module
|
|
which is 19200bps.
|
|
|
|
.. warning::
|
|
|
|
If you are using the :doc:`logger` make sure you disable the uart logging with the
|
|
``baud_rate: 0`` option.
|
|
|
|
.. figure:: images/rf_bridge-full.jpg
|
|
:align: center
|
|
:width: 60.0%
|
|
|
|
.. code-block:: yaml
|
|
|
|
# Example configuration entry
|
|
uart:
|
|
baud_rate: 19200
|
|
|
|
rf_bridge:
|
|
on_code_received:
|
|
- homeassistant.event:
|
|
event: esphome.rf_code_received
|
|
data:
|
|
sync: !lambda 'char buffer [10];return itoa(data.sync,buffer,16);'
|
|
low: !lambda 'char buffer [10];return itoa(data.low,buffer,16);'
|
|
high: !lambda 'char buffer [10];return itoa(data.high,buffer,16);'
|
|
code: !lambda 'char buffer [10];return itoa(data.code,buffer,16);'
|
|
|
|
Configuration variables:
|
|
------------------------
|
|
|
|
- **uart_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the UART hub.
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation.
|
|
- **on_code_received** (*Optional*, :ref:`Automation <automation>`): An action to be
|
|
performed when a code is received. See :ref:`rf_bridge-on_code_received`.
|
|
|
|
.. _rf_bridge-on_code_received:
|
|
|
|
``on_code_received`` Trigger
|
|
----------------------------
|
|
|
|
With this configuration option you can write complex automations whenever a code is
|
|
received. To use the code, use a :ref:`lambda <config-lambda>` template, the code
|
|
and the corresponding protocol timings are available inside that lambda under the
|
|
variables named ``code``, ``sync``, ``high`` and ``low``.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_code_received:
|
|
- homeassistant.event:
|
|
event: esphome.rf_code_received
|
|
data:
|
|
sync: !lambda 'char buffer [10];return itoa(data.sync,buffer,16);'
|
|
low: !lambda 'char buffer [10];return itoa(data.low,buffer,16);'
|
|
high: !lambda 'char buffer [10];return itoa(data.high,buffer,16);'
|
|
code: !lambda 'char buffer [10];return itoa(data.code,buffer,16);'
|
|
|
|
|
|
.. _rf_bridge-send_code_action:
|
|
|
|
``rf_bridge.send_code`` Action
|
|
------------------------------
|
|
|
|
Send an RF code using this action in automations.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
- rf_bridge.send_code:
|
|
sync: 0x700
|
|
low: 0x800
|
|
high: 0x1000
|
|
code: 0xABC123
|
|
|
|
Configuration options:
|
|
|
|
- **sync** (**Required**, int, :ref:`templatable <config-templatable>`): RF Sync timing
|
|
- **low** (**Required**, int, :ref:`templatable <config-templatable>`): RF Low timing
|
|
- **high** (**Required**, int, :ref:`templatable <config-templatable>`): RF high timing
|
|
- **code** (**Required**, int, :ref:`templatable <config-templatable>`): RF code
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
|
|
|
|
.. note::
|
|
|
|
This action can also be written in :ref:`lambdas <config-lambda>`:
|
|
|
|
.. code-block:: cpp
|
|
|
|
id(rf_bridge).send_code(0x700, 0x800, 0x1000, 0xABC123);
|
|
|
|
|
|
.. _rf_bridge-send_raw_action:
|
|
|
|
``rf_bridge.send_raw`` Action
|
|
-----------------------------
|
|
|
|
Send a raw RF code using this action in automations.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
- rf_bridge.send_raw:
|
|
raw: AAA5070008001000ABC12355
|
|
|
|
Configuration options:
|
|
|
|
- **raw** (**Required**, string, :ref:`templatable <config-templatable>`): RF raw string
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
|
|
|
|
.. note::
|
|
|
|
This action can also be written in :ref:`lambdas <config-lambda>`:
|
|
|
|
.. code-block:: cpp
|
|
|
|
id(rf_bridge).send_raw("AAA5070008001000ABC12355");
|
|
|
|
|
|
.. _rf_bridge-learn_action:
|
|
|
|
``rf_bridge.learn`` Action
|
|
--------------------------
|
|
|
|
Tell the RF Bridge to learn new protocol timings using this action in automations.
|
|
A new code with timings will be returned to :ref:`rf_bridge-on_code_received`
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
- rf_bridge.learn
|
|
|
|
Configuration options:
|
|
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
|
|
|
|
.. note::
|
|
|
|
This action can also be written in :ref:`lambdas <config-lambda>`:
|
|
|
|
.. code-block:: cpp
|
|
|
|
id(rf_bridge).learn();
|
|
|
|
|
|
Portisch firmware
|
|
-----------------
|
|
|
|
If you have flashed the secondary MCU with the `Portisch firmware <https://github.com/Portisch/RF-Bridge-EFM8BB1>`__,
|
|
ESPHome is able to receive the extra protocols that can be decoded as well as activate the other modes supported.
|
|
|
|
|
|
.. _rf_bridge-on_advanced_code_received:
|
|
|
|
``on_advanced_code_received`` Trigger
|
|
-------------------------------------
|
|
|
|
Similar to :ref:`rf_bridge-on_code_received`, this trigger receives the codes after advanced sniffing is started.
|
|
To use the code, use a :ref:`lambda <config-lambda>` template, the code and the corresponding protocol and length
|
|
are available inside that lambda under the variables named ``code``, ``protocol`` and ``length``.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_advanced_code_received:
|
|
- homeassistant.event:
|
|
event: esphome.rf_advanced_code_received
|
|
data:
|
|
length: !lambda 'char buffer [10];return itoa(data.length,buffer,16);'
|
|
protocol: !lambda 'char buffer [10];return itoa(data.protocol,buffer,16);'
|
|
code: !lambda 'return data.code;'
|
|
|
|
|
|
.. _rf_bridge-send_advanced_code_action:
|
|
|
|
``rf_bridge.send_advanced_code`` Action
|
|
---------------------------------------
|
|
|
|
Send an RF code using this action in automations.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
- rf_bridge.send_advanced_code:
|
|
length: 0x04
|
|
protocol: 0x01
|
|
code: "ABC123"
|
|
|
|
Configuration options:
|
|
|
|
- **length** (**Required**, int, :ref:`templatable <config-templatable>`): Length of code plus protocol
|
|
- **protocol** (**Required**, int, :ref:`templatable <config-templatable>`): RF Protocol
|
|
- **code** (**Required**, string, :ref:`templatable <config-templatable>`): RF code
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
|
|
|
|
.. note::
|
|
|
|
This action can also be written in :ref:`lambdas <config-lambda>`:
|
|
|
|
.. code-block:: cpp
|
|
|
|
id(rf_bridge).send_advanced_code(0x04, 0x01, "ABC123");
|
|
|
|
|
|
.. _rf_bridge-start_advanced_sniffing_action:
|
|
|
|
``rf_bridge.start_advanced_sniffing`` Action
|
|
--------------------------------------------
|
|
|
|
Tell the RF Bridge to listen for the advanced/extra protocols defined in the portisch firmware.
|
|
The decoded codes with length and protocol will be returned to :ref:`rf_bridge-on_advanced_code_received`
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
- rf_bridge.start_advanced_sniffing
|
|
|
|
Configuration options:
|
|
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
|
|
|
|
.. note::
|
|
|
|
This action can also be written in :ref:`lambdas <config-lambda>`:
|
|
|
|
.. code-block:: cpp
|
|
|
|
id(rf_bridge).start_advanced_sniffing();
|
|
|
|
|
|
.. _rf_bridge-stop_advanced_sniffing_action:
|
|
|
|
``rf_bridge.stop_advanced_sniffing`` Action
|
|
-------------------------------------------
|
|
|
|
Tell the RF Bridge to stop listening for the advanced/extra protocols defined in the portisch firmware.
|
|
|
|
.. code-block:: yaml
|
|
|
|
on_...:
|
|
then:
|
|
- rf_bridge.stop_advanced_sniffing
|
|
|
|
Configuration options:
|
|
|
|
- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the RF Bridge if you have multiple components.
|
|
|
|
.. note::
|
|
|
|
This action can also be written in :ref:`lambdas <config-lambda>`:
|
|
|
|
.. code-block:: cpp
|
|
|
|
id(rf_bridge).stop_advanced_sniffing();
|
|
|
|
|
|
Getting started with Home Assistant
|
|
-----------------------------------
|
|
|
|
The following code will get you up and running with a configuration sending codes to
|
|
Home Assistant as events and will also setup a service so you can send codes with your RF Bridge.
|
|
|
|
.. code-block:: yaml
|
|
|
|
api:
|
|
services:
|
|
- service: send_rf_code
|
|
variables:
|
|
sync: int
|
|
low: int
|
|
high: int
|
|
code: int
|
|
then:
|
|
- rf_bridge.send_code:
|
|
sync: !lambda 'return sync;'
|
|
low: !lambda 'return low;'
|
|
high: !lambda 'return high;'
|
|
code: !lambda 'return code;'
|
|
- service: learn
|
|
then:
|
|
- rf_bridge.learn
|
|
|
|
uart:
|
|
tx_pin: 1
|
|
rx_pin: 3
|
|
baud_rate: 19200
|
|
|
|
logger:
|
|
baud_rate: 0
|
|
|
|
rf_bridge:
|
|
on_code_received:
|
|
then:
|
|
- homeassistant.event:
|
|
event: esphome.rf_code_received
|
|
data:
|
|
sync: !lambda 'char buffer [10];return itoa(data.sync,buffer,16);'
|
|
low: !lambda 'char buffer [10];return itoa(data.low,buffer,16);'
|
|
high: !lambda 'char buffer [10];return itoa(data.high,buffer,16);'
|
|
code: !lambda 'char buffer [10];return itoa(data.code,buffer,16);'
|
|
|
|
|
|
Now your latest received code will be in an event.
|
|
|
|
To trigger the automation from Home Assistant you can invoke the service with this code:
|
|
|
|
.. code-block:: yaml
|
|
|
|
automation:
|
|
# ...
|
|
action:
|
|
- service: esphome.rf_bridge_send_rf_code
|
|
data:
|
|
sync: 0x700
|
|
low: 0x800
|
|
high: 0x1000
|
|
code: 0xABC123
|
|
|
|
See Also
|
|
--------
|
|
|
|
- :apiref:`rf_bridge/rf_bridge.h`
|
|
- :doc:`/components/uart`
|
|
- :ghedit:`Edit`
|