mirror of
https://github.com/goharbor/harbor.git
synced 2024-11-09 04:01:14 +01:00
585 lines
27 KiB
Markdown
585 lines
27 KiB
Markdown
# Installation and Configuration Guide
|
|
|
|
There are two possibilities when installing Harbor.
|
|
|
|
- **Online installer:** The online installer downloads the Harbor images from Docker hub. For this reason, the installer is very small in size.
|
|
|
|
- **Offline installer:** Use the offline installer if the host to which are are deploying Harbor does not have a connection to the Internet. The offline installer contains pre-built images so it is larger than the online installer.
|
|
|
|
You download the installers from the **[official release](https://github.com/goharbor/harbor/releases)** page.
|
|
|
|
This guide describes how to install and configure Harbor by using either the online or offline installer. The installation processes are almost the same.
|
|
|
|
If you are upgrading from a previous version of Harbor, you might need to update the configuration file and migrate your data to fit the database schema of the later version. For information about upgrading, see the **[Harbor Upgrade and Migration Guide](migration_guide.md)**.
|
|
|
|
In addition, the Harbor community created instructions describing how to deploy Harbor on Kubernetes. If you want to deploy Harbor to Kubernetes, see [Harbor on Kubernetes](kubernetes_deployment.md).
|
|
|
|
## Harbor Components
|
|
|
|
The table below lists the components that are deployed when you deploy Harbor.
|
|
|
|
|Component|Version|
|
|
|---|---|
|
|
|Postgresql|9.6.10-1.ph2|
|
|
|Redis|4.0.10-1.ph2|
|
|
|Clair|2.0.8|
|
|
|Beego|1.9.0|
|
|
|Chartmuseum|0.9.0|
|
|
|Docker/distribution|2.7.1|
|
|
|Docker/notary|0.6.1|
|
|
|Helm|2.9.1|
|
|
|Swagger-ui|3.22.1|
|
|
|
|
## Deployment Prerequisites for the Target Host
|
|
|
|
Harbor is deployed as several Docker containers. You can therefore deploy it on any Linux distribution that supports Docker. The target host requires Docker, and Docker Compose to be installed.
|
|
|
|
### Hardware
|
|
|
|
The following table lists the minimum and recommended hardware configurations for deploying Harbor.
|
|
|
|
|Resource|Minimum|Recommended|
|
|
|---|---|---|
|
|
|CPU|2 CPU|4 CPU|
|
|
|Mem|4 GB|8 GB|
|
|
|Disk|40 GB|160 GB|
|
|
|
|
### Software
|
|
|
|
The following table lists the software versions that must be installed on the target host.
|
|
|
|
|Software|Version|Description|
|
|
|---|---|---|
|
|
|Docker engine|version 17.06.0-ce+ or higher|For installation instructions, see [docker engine doc](https://docs.docker.com/engine/installation/)|
|
|
|Docker Compose|version 1.18.0 or higher|For installation instructions, see [docker compose doc](https://docs.docker.com/compose/install/)|
|
|
|Openssl|latest is preferred|Used to generate certificate and keys for Harbor|
|
|
|
|
### Network ports
|
|
|
|
Harbor requires that the following ports be open on the target host.
|
|
|
|
|Port|Protocol|Description|
|
|
|---|---|---|
|
|
|443|HTTPS|Harbor portal and core API accept HTTPS requests on this port. You can change this port in the configuration file.|
|
|
|4443|HTTPS|Connections to the Docker Content Trust service for Harbor. Only required if Notary is enabled. You can change this port in the configuration file.|
|
|
|80|HTTP|Harbor portal and core API accept HTTP requests on this port. You can change this port in the configuration file.|
|
|
|
|
## Installation Procedure
|
|
|
|
The installation procedure involves the following steps:
|
|
|
|
1. Download the installer.
|
|
2. Configure the **harbor.yml** file.
|
|
3. Run the **install.sh** script with the appropriate options to install and start Harbor.
|
|
|
|
## Download the Installer
|
|
|
|
1. Go to the [Harbor releases page](https://github.com/goharbor/harbor/releases).
|
|
1. Select either the online or offline installer for the version you want to install.
|
|
1. Use `tar` to extract the installer package:
|
|
|
|
- Online installer:<pre>bash $ tar xvf harbor-online-installer-<em>version</em>.tgz</pre>
|
|
- Offline installer:<pre>bash $ tar xvf harbor-offline-installer-<em>version</em>.tgz</pre>
|
|
|
|
## Configure Harbor
|
|
|
|
You set system level parameters for Harbor in the `harbor.yml` file that is contained in the installer package. These parameters take effect when you run the `install.sh` script to install or reconfigure Harbor.
|
|
|
|
After the initial deployment and after you have started Harbor, you perform additional configuration in the Harbor Web Portal.
|
|
|
|
### Required Parameters
|
|
|
|
The table below lists the parameters that must be set when you deploy Harbor. At the very least, you must update the `hostname` parameter.
|
|
|
|
**IMPORTANT**: Harbor does not ship with any certificates, and by default uses HTTP to serve registry requests. This is acceptable only in air-gapped test or development environments. In production environments, always use HTTPS. If you enable Content Trust with Notary, you must use HTTPS.
|
|
|
|
You can use certificates that are signed by a trusted third-party CA, or you can use self-signed certificates. For information about how to create a CA, and how to use a CA to sign a server certificate and a client certificate, see **[Configuring Harbor with HTTPS Access](configure_https.md)**.
|
|
|
|
<table width="100%" border="0">
|
|
<caption>
|
|
Required Parameters for Harbor Deployment
|
|
</caption>
|
|
<tr>
|
|
<th scope="col">Parameter</th>
|
|
<th scope="col">Sub-parameters</th>
|
|
<th scope="col">Description and Additional Parameters </th>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>hostname</code></td>
|
|
<td valign="top">None</td>
|
|
<td valign="top">Specify the IP address or the fully qualified domain name (FQDN) of the target host on which to deploy Harbor. This is the address at which you access the Harbor Portal and the registry service. For example, <code>192.168.1.10</code> or <code>reg.yourdomain.com</code>. The registry service must be accessible to external clients, so do not specify <code>localhost</code>, <code>127.0.0.1</code>, or <code>0.0.0.0</code> as the hostname.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>https</code></td>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><p>Use HTTPS to access the Harbor Portal and the token/notification service. </p>
|
|
</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>port</code></td>
|
|
<td valign="top">The port number for HTTPS. The default is 443.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>certificate</code></td>
|
|
<td valign="top">The path to the SSL certificate.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>private_key</code></td>
|
|
<td valign="top">The path to the SSL key.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>harbor_admin_password</code></td>
|
|
<td valign="top">None</td>
|
|
<td valign="top">Set an initial password for the Harbor administrator. This password is only used on the first time that Harbor starts. On subsequent logins, this setting is ignored and the administrator's password is set in the Harbor Portal. The default username and password are `admin` and `Harbor12345`.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>database</code></td>
|
|
<td valign="top"> </td>
|
|
<td valign="top">Use a local PostgreSQL database. You can optionally configure an external database, in which case disable this option.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>password</code></td>
|
|
<td valign="top">Set the root password for the local database. You must change this password for production deployments.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>max_idle_conns</code></td>
|
|
<td valign="top">The maximum number of connections in the idle connection pool. If set to <=0 no idle connections are retained. The default value is 50. If it is not configured the value is 2.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>max_open_conns</code></td>
|
|
<td valign="top">The maximum number of open connections to the database. If <= 0 there is no limit on the number of open connections. The default value is 100 for the max connections to the Harbor database. If it is not configured the value is 0.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>data_volume</code></td>
|
|
<td valign="top">None</td>
|
|
<td valign="top">The location on the target host in which to store Harbor's data. You can optionally configure external storage, in which case disable this option and enable `storage_service`.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>jobservice</code></td>
|
|
<td valign="top"> </td>
|
|
<td valign="top">Configure the replication job service.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>max_job_workers</code></td>
|
|
<td valign="top">The maximum number of replication workers in the job service. For each image replication job, a worker synchronizes all tags of a repository to the remote destination. Increasing this number allows more concurrent replication jobs in the system. However, since each worker consumes a certain amount of network/CPU/IO resources, set the value of this attribute based on the hardware resource of the host.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>log</code></td>
|
|
<td valign="top"> </td>
|
|
<td valign="top">Configure logging.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>level</code></td>
|
|
<td valign="top">Set the logging level to <code>debug</code>, <code>info</code>, <code>warning</code>, <code>error</code>, or <code>fatal</code>.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>local</code></td>
|
|
<td valign="top">Optionally disable this option to use <code>external_endpoint</code> to send logs to Syslog. If you use local logging, set the following parameters:<ul>
|
|
<li><code>rotate_count</code>: Log files are rotated <code>rotate_count</code> times before being removed. If count is 0, old versions are removed rather than rotated.</li>
|
|
<li><code>rotate_size</code>: Log files are rotated only if they grow bigger than <code>rotate_size</code> bytes. Use <code>k</code> for kilobytes, <code>M</code> for megabytes, and <code>G</code> for gigabytes. <code>100</code>, <code>100k</code>, <code>100M</code> and <code>100G</code> are all valid values.</li>
|
|
<li><code>location</code>: Set the directory in which to store the logs.</li>
|
|
</ul></td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>external_endpoint</code></td>
|
|
<td valign="top">Enable this option to forward logs to a syslog server.
|
|
<ul>
|
|
<li><code>protocol</code>: Transport protocol for the syslog server. Default is TCP.</li>
|
|
<li><code>host</code>: The URL of the syslog server.</li>
|
|
<li><code>port</code>: The port on which the syslog server listens</li>
|
|
</ul> </td>
|
|
</tr>
|
|
</table>
|
|
|
|
### Optional parameters
|
|
|
|
<table width="100%" border="0">
|
|
<caption>
|
|
Optional Parameters for Harbor
|
|
</caption>
|
|
<tr>
|
|
<th scope="col">Parameter</th>
|
|
<th scope="col">Sub-Parameters</th>
|
|
<th scope="col">Description and Additional Parameters </th>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>http</code></td>
|
|
<td valign="top"> </td>
|
|
<td valign="top">Do not use HTTP in production environments. Using HTTP is acceptable only in air-gapped test or development environments that do not have a connection to the external internet. Using HTTP in environments that are not air-gapped exposes you to man-in-the-middle attacks.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>port</code></td>
|
|
<td valign="top">Port number for HTTP</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>external_url</code></td>
|
|
<td valign="top">None</td>
|
|
<td valign="top">Enable it if use external proxy, and when it enabled the hostname will no longer used</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>clair</code></td>
|
|
<td valign="top"> </td>
|
|
<td valign="top">Clair related configs</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>updaters_interval</code></td>
|
|
<td valign="top">The interval of clair updaters, the unit is hour, set to 0 to disable the updaters</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>http_proxy</code></td>
|
|
<td valign="top">Config http proxy for Clair, e.g. <code>http://my.proxy.com:3128</code>.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>https_proxy</code></td>
|
|
<td valign="top">Config https proxy for Clair, e.g. <code>http://my.proxy.com:3128</code>.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>no_proxy</code></td>
|
|
<td valign="top">Config no proxy for Clair, e.g. <code>127.0.0.1,localhost,core,registry</code>.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>chart</code></td>
|
|
<td valign="top"> </td>
|
|
<td valign="top">chart related configs</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>absolute_url</code></td>
|
|
<td valign="top">if set to enabled chart will use absolute url, otherwise set it to disabled, chart will use relative url.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>external_database</code></td>
|
|
<td valign="top"> </td>
|
|
<td valign="top">external database configs, Currently only support POSTGRES.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>harbor</code></td>
|
|
<td valign="top"><p>harbor’s core database configs</p>
|
|
<ul>
|
|
<li><code>host</code>: hostname for harbor core database</li>
|
|
<li><code>port</code>: port of harbor’s core database</li>
|
|
<li><code>db_name</code>: database name of harbor core database</li>
|
|
<li><code>username</code>: username to connect harbor core database</li>
|
|
<li><code>password</code>: password to harbor core database</li>
|
|
<li><code>ssl_mode</code>: is enable ssl mode</li>
|
|
<li><code>max_idle_conns</code>: The maximum number of connections in the idle connection pool. If <=0 no idle connections are retained. The default value is 2.</li>
|
|
<li><code>max_open_conns</code>: The maximum number of open connections to the database. If <= 0 there is no limit on the number of open connections. The default value is 0.</li>
|
|
</ul> </td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>clair</code></td>
|
|
<td valign="top">clair’s database configs
|
|
<ul>
|
|
<li><code>host</code>: hostname for clair database</li>
|
|
<li><code>port</code>: port of clair database</li>
|
|
<li><code>db_name</code>: database name of clair database</li>
|
|
<li><code>username</code>: username to connect clair database</li>
|
|
<li><code>password</code>: password to clair database</li>
|
|
<li><code>ssl_mode</code>: is enable ssl mode</li>
|
|
</ul> </td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>notary_signer</code></td>
|
|
<td valign="top">notary’s signer database configs
|
|
<ul>
|
|
<li><code>host</code>: hostname for notary signer database</li>
|
|
<li><code>port</code>: port of notary signer database</li>
|
|
<li><code>db_name</code>: database name of notary signer database</li>
|
|
<li><code>username</code>: username to connect notary signer database</li>
|
|
<li><code>password</code>: password to notary signer database</li>
|
|
<li><code>ssl_mode</code>: is enable ssl mode</li>
|
|
</ul> </td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>notary_server</code></td>
|
|
<td valign="top"><ul>
|
|
<li><code>host</code>: hostname for notary server database</li>
|
|
<li><code>port</code>: port of notary server database</li>
|
|
<li><code>db_name</code>: database name of notary server database</li>
|
|
<li><code>username</code>: username to connect notary server database</li>
|
|
<li><code>password</code>: password to notary server database</li>
|
|
<li><code>ssl_mode</code>: is enable ssl mode</li>
|
|
</ul> </td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>external_redis</code></td>
|
|
<td valign="top"> </td>
|
|
<td valign="top">configs for use the external redis</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>host</code></td>
|
|
<td valign="top">host for external redis</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>port</code></td>
|
|
<td valign="top">port for external redis</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>password</code></td>
|
|
<td valign="top">password to connect external host</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>registry_db_index</code></td>
|
|
<td valign="top">db index for registry use</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>jobservice_db_index</code></td>
|
|
<td valign="top">db index for jobservice</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>chartmuseum_db_index</code></td>
|
|
<td valign="top">db index for chartmuseum </td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"><code>storage_service</code></td>
|
|
<td valign="top"> </td>
|
|
<td valign="top">By default, Harbor stores images and charts on your local filesystem. In a production environment, you may consider use other storage backend instead of the local filesystem, like S3, OpenStack Swift, Ceph, etc. These parameters are configurations for registry. See *Configuring Storage Backend* below for more information.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>ca_bundle</code></td>
|
|
<td valign="top">The path to the custom root ca certificate, which will be injected into the trust store of registry's and chart repository's containers. This is usually needed when the user hosts a internal storage with self signed certificate.</td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>provider_name</code></td>
|
|
<td valign="top">Storage configs for registry, default is filesystem. for more info about this configuration please refer <a href="https://docs.docker.com/registry/configuration/" rel="nofollow">https://docs.docker.com/registry/configuration/</a></td>
|
|
</tr>
|
|
<tr>
|
|
<td valign="top"> </td>
|
|
<td valign="top"><code>redirect</code></td>
|
|
<td valign="top"><code>disable</code>: set disable to true when you want to disable registry redirect</td>
|
|
</tr>
|
|
</table>
|
|
|
|
#### Configuring storage backend (optional)
|
|
|
|
For example, if you use Openstack Swift as your storage backend, the parameters may look like this:
|
|
|
|
``` yaml
|
|
storage_service:
|
|
ca_bundle:
|
|
swift:
|
|
username: admin
|
|
password: ADMIN_PASS
|
|
authurl: http://keystone_addr:35357/v3/auth
|
|
tenant: admin
|
|
domain: default
|
|
region: regionOne
|
|
container: docker_images"
|
|
redirect:
|
|
disable: false
|
|
```
|
|
|
|
_NOTE: For detailed information on storage backend of a registry, refer to [Registry Configuration Reference](https://docs.docker.com/registry/configuration/) ._
|
|
|
|
## Finishing installation and starting Harbor
|
|
|
|
Once **harbor.yml** and storage backend (optional) are configured, install and start Harbor using the `install.sh` script. Note that it may take some time for the online installer to download Harbor images from Docker hub.
|
|
|
|
### Default installation (without Notary/Clair)
|
|
|
|
Harbor has integrated with Notary and Clair (for vulnerability scanning). However, the default installation does not include Notary or Clair service.
|
|
|
|
``` sh
|
|
$ sudo ./install.sh
|
|
```
|
|
|
|
If everything worked properly, you should be able to open a browser to visit the admin portal at `http://reg.yourdomain.com` (change `reg.yourdomain.com` to the hostname configured in your `harbor.yml`). Note that the default administrator username/password are admin/Harbor12345.
|
|
|
|
Log in to the admin portal and create a new project, e.g. `myproject`. You can then use docker commands to login and push images (By default, the registry server listens on port 80):
|
|
|
|
```sh
|
|
$ docker login reg.yourdomain.com
|
|
$ docker push reg.yourdomain.com/myproject/myrepo:mytag
|
|
```
|
|
|
|
**IMPORTANT:** The default installation of Harbor uses _HTTP_ - as such, you will need to add the option `--insecure-registry` to your client's Docker daemon and restart the Docker service.
|
|
|
|
### Installation with Notary
|
|
To install Harbor with Notary service, add a parameter when you run `install.sh`:
|
|
|
|
```sh
|
|
$ sudo ./install.sh --with-notary
|
|
```
|
|
|
|
**Note**: For installation with Notary the parameter **ui_url_protocol** must be set to "https". For configuring HTTPS please refer to the following sections.
|
|
|
|
More information about Notary and Docker Content Trust, please refer to [Docker's documentation](https://docs.docker.com/engine/security/trust/content_trust/).
|
|
|
|
### Installation with Clair
|
|
|
|
To install Harbor with Clair service, add a parameter when you run `install.sh`:
|
|
|
|
```sh
|
|
$ sudo ./install.sh --with-clair
|
|
```
|
|
|
|
For more information about Clair, please refer to Clair's documentation:
|
|
`https://coreos.com/clair/docs/2.0.1/`
|
|
|
|
### Installation with chart repository service
|
|
|
|
To install Harbor with chart repository service, add a parameter when you run ```install.sh```:
|
|
|
|
```sh
|
|
$ sudo ./install.sh --with-chartmuseum
|
|
```
|
|
|
|
**Note**: If you want to install Notary, Clair and chart repository service, you must specify all the parameters in the same command:
|
|
|
|
```sh
|
|
$ sudo ./install.sh --with-notary --with-clair --with-chartmuseum
|
|
```
|
|
|
|
For information on how to use Harbor, please refer to **[User Guide of Harbor](user_guide.md)** .
|
|
|
|
## Configuring Harbor with HTTPS access
|
|
|
|
Harbor does not ship with any certificates, and, by default, uses HTTP to serve requests. While this makes it relatively simple to set up and run - especially for a development or testing environment - it is **not** recommended for a production environment. To enable HTTPS, please refer to **[Configuring Harbor with HTTPS Access](configure_https.md)**.
|
|
|
|
## Managing Harbor's lifecycle
|
|
|
|
You can use docker-compose to manage the lifecycle of Harbor. Some useful commands are listed as follows (must run in the same directory as *docker-compose.yml*).
|
|
|
|
Stopping Harbor:
|
|
|
|
``` sh
|
|
$ sudo docker-compose stop
|
|
Stopping nginx ... done
|
|
Stopping harbor-portal ... done
|
|
Stopping harbor-jobservice ... done
|
|
Stopping harbor-core ... done
|
|
Stopping registry ... done
|
|
Stopping redis ... done
|
|
Stopping registryctl ... done
|
|
Stopping harbor-db ... done
|
|
Stopping harbor-log ... done
|
|
```
|
|
|
|
Restarting Harbor after stopping:
|
|
|
|
``` sh
|
|
$ sudo docker-compose start
|
|
Starting log ... done
|
|
Starting registry ... done
|
|
Starting registryctl ... done
|
|
Starting postgresql ... done
|
|
Starting core ... done
|
|
Starting portal ... done
|
|
Starting redis ... done
|
|
Starting jobservice ... done
|
|
Starting proxy ... done
|
|
```
|
|
|
|
To change Harbor's configuration, first stop existing Harbor instance and update `harbor.yml`. Then run `prepare` script to populate the configuration. Finally re-create and start Harbor's instance:
|
|
|
|
``` sh
|
|
$ sudo docker-compose down -v
|
|
$ vim harbor.yml
|
|
$ sudo prepare
|
|
$ sudo docker-compose up -d
|
|
```
|
|
|
|
Removing Harbor's containers while keeping the image data and Harbor's database files on the file system:
|
|
|
|
``` sh
|
|
$ sudo docker-compose down -v
|
|
```
|
|
|
|
Removing Harbor's database and image data (for a clean re-installation):
|
|
|
|
``` sh
|
|
$ rm -r /data/database
|
|
$ rm -r /data/registry
|
|
```
|
|
|
|
### *Managing lifecycle of Harbor when it's installed with Notary, Clair and chart repository service*
|
|
|
|
If you want to install Notary, Clair and chart repository service together, you should include all the components in the prepare commands:
|
|
|
|
``` sh
|
|
$ sudo docker-compose down -v
|
|
$ vim harbor.yml
|
|
$ sudo prepare --with-notary --with-clair --with-chartmuseum
|
|
$ sudo docker-compose up -d
|
|
```
|
|
|
|
Please check the [Docker Compose command-line reference](https://docs.docker.com/compose/reference/) for more on docker-compose.
|
|
|
|
## Persistent data and log files
|
|
|
|
By default, registry data is persisted in the host's `/data/` directory. This data remains unchanged even when Harbor's containers are removed and/or recreated, you can edit the `data_volume` in `harbor.yml` file to change this directory.
|
|
|
|
In addition, Harbor uses *rsyslog* to collect the logs of each container. By default, these log files are stored in the directory `/var/log/harbor/` on the target host for troubleshooting, also you can change the log directory in `harbor.yml`.
|
|
|
|
## Configuring Harbor listening on a customized port
|
|
|
|
By default, Harbor listens on port 80(HTTP) and 443(HTTPS, if configured) for both admin portal and docker commands, these default ports can configured in `harbor.yml`
|
|
|
|
## Configuring Harbor using the external database
|
|
|
|
Currently, only PostgreSQL database is supported by Harbor.
|
|
To user an external database, just uncomment the `external_database` section in `harbor.yml` and fill the necessary information. Four databases are needed to be create first by users for Harbor core, Clair, Notary server and Notary signer. And the tables will be generated automatically when Harbor starting up.
|
|
|
|
## Manage user settings
|
|
|
|
User settings are handled separately system settings. All user settings are configured in the web console or by HTTP requests at the command line. For information about using HTTP requests to configure user settings, see [Configure User Settings at the Command Line](configure_user_settings.md) to config user settings.
|
|
|
|
## Performance tuning
|
|
|
|
By default, Harbor limits the CPU usage of Clair container to 150000 and avoids its using up all the CPU resources. This is defined in the docker-compose.clair.yml file. You can modify it based on your hardware configuration.
|
|
|
|
## Troubleshooting
|
|
|
|
1. When Harbor does not work properly, run the below commands to find out if all containers of Harbor are in **UP** status:
|
|
```
|
|
$ sudo docker-compose ps
|
|
Name Command State Ports
|
|
-----------------------------------------------------------------------------------------------------------------------------
|
|
harbor-core /harbor/start.sh Up
|
|
harbor-db /entrypoint.sh postgres Up 5432/tcp
|
|
harbor-jobservice /harbor/start.sh Up
|
|
harbor-log /bin/sh -c /usr/local/bin/ ... Up 127.0.0.1:1514->10514/tcp
|
|
harbor-portal nginx -g daemon off; Up 80/tcp
|
|
nginx nginx -g daemon off; Up 0.0.0.0:443->443/tcp, 0.0.0.0:4443->4443/tcp, 0.0.0.0:80->80/tcp
|
|
redis docker-entrypoint.sh redis ... Up 6379/tcp
|
|
registry /entrypoint.sh /etc/regist ... Up 5000/tcp
|
|
registryctl /harbor/start.sh Up
|
|
```
|
|
|
|
If a container is not in **UP** state, check the log file of that container in directory `/var/log/harbor`. For example, if the container `harbor-core` is not running, you should look at the log file `core.log`.
|
|
|
|
2.When setting up Harbor behind an nginx proxy or elastic load balancing, look for the line below, in `common/config/nginx/nginx.conf` and remove it from the sections if the proxy already has similar settings: `location /`, `location /v2/` and `location /service/`.
|
|
|
|
``` sh
|
|
proxy_set_header X-Forwarded-Proto $scheme;
|
|
```
|
|
|
|
and re-deploy Harbor refer to the previous section "Managing Harbor's lifecycle".
|