New branding for ESPHome (#3926)

* Update for higher i2c frequencies on IDF

* Update sht3xd.rst

.devcontainer/devcontainer.json

@@ -2,7 +2,7 @@
 {
   "name": "ESPHome - docs",
   "image": "mcr.microsoft.com/vscode/devcontainers/python:0-3.11",
-  "postCreateCommand": "pip3 install -r requirements.txt -r requirements_test.txt",
+  "postCreateCommand": ".devcontainer/postCreate.sh",
   "postAttachCommand": "make live-html",
   "forwardPorts": [8000],
   "features": {

.devcontainer/postCreate.sh

@@ -0,0 +1,5 @@
+#!/bin/bash
+
+
+pip3 install -r requirements.txt -r requirements_test.txt
+curl -L https://github.com/CloudCannon/pagefind/releases/download/v1.1.0/pagefind-v1.1.0-x86_64-unknown-linux-musl.tar.gz | tar -xz -C ~/.local/bin

.github/workflows/docker.yml

@@ -18,9 +18,14 @@ jobs:
   build:
     runs-on: ubuntu-latest
     steps:
+      -
+        name: Install pagefind
+        uses: jaxxstorm/action-install-gh-release@v1.12.0
+        with:
+          repo: cloudcannon/pagefind
       -
         name: Checkout source code
-        uses: actions/checkout@v4.1.0
+        uses: actions/checkout@v4.1.6
       -
         name: Set up QEMU
         uses: docker/setup-qemu-action@v3

.github/workflows/lint.yml

@@ -19,7 +19,11 @@ jobs:
   build:
     runs-on: ubuntu-latest
     steps:
-    - uses: actions/checkout@v4.1.0
+    - name: Install pagefind
+      uses: jaxxstorm/action-install-gh-release@v1.12.0
+      with:
+          repo: cloudcannon/pagefind
+    - uses: actions/checkout@v4.1.6
     - name: Set up Python 3.8
       uses: actions/setup-python@v5
       with:

.gitignore

@@ -11,3 +11,5 @@ venv
 .vscode
 *.DS_Store
 /.idea/
+
+_pagefind/

Dockerfile

@@ -1,4 +1,4 @@
-FROM python:3.8-slim
+FROM python:3.12-slim
 
 RUN apt-get update && apt-get install -y --no-install-recommends \
         curl \
@@ -9,10 +9,39 @@ RUN apt-get update && apt-get install -y --no-install-recommends \
         software-properties-common \
         && apt-get clean && rm -rf /var/lib/apt/lists/* /tmp/*
 
-COPY requirements.txt .
+ENV PAGEFIND_VERSION="1.1.0"
+ARG TARGETARCH
+SHELL ["/bin/bash", "-c"]
+RUN <<EOF
+    export TARGETARCH=${TARGETARCH/arm64/aarch64}
+    export TARGETARCH=${TARGETARCH/amd64/x86_64}
+    curl -o pagefind.tar.gz https://github.com/CloudCannon/pagefind/releases/download/v$PAGEFIND_VERSION/pagefind-v$PAGEFIND_VERSION-$TARGETARCH-unknown-linux-musl.tar.gz -L
+    tar xzf pagefind.tar.gz
+    rm pagefind.tar.gz
+    mv pagefind /usr/bin
+    chmod +x /usr/bin/pagefind
+EOF
+
+RUN useradd -ms /bin/bash esphome
+
+
+USER esphome
+
+WORKDIR /workspaces/esphome-docs
+ENV PATH="${PATH}:/home/esphome/.local/bin"
+
+COPY requirements.txt ./
 RUN pip3 install --no-cache-dir --no-binary :all: -r requirements.txt
 
 EXPOSE 8000
-WORKDIR /data/esphomedocs
 
 CMD ["make", "live-html"]
+
+LABEL \
+        org.opencontainers.image.title="esphome-docs" \
+        org.opencontainers.image.description="An image to help with ESPHomes documentation development" \
+        org.opencontainers.image.vendor="ESPHome" \
+        org.opencontainers.image.licenses="CC BY-NC-SA 4.0" \
+        org.opencontainers.image.url="https://esphome.io" \
+        org.opencontainers.image.source="https://github.com/esphome/esphome-docs" \
+        org.opencontainers.image.documentation="https://github.com/esphome/esphome-docs/blob/current/README.md"

Doxygen

@@ -38,7 +38,7 @@ PROJECT_NAME           = "ESPHome"
 # could be handy for archiving the generated documentation or if some version
 # control system is used.
 
-PROJECT_NUMBER         = 2024.3.1
+PROJECT_NUMBER         = 2024.5.5
 
 # Using the PROJECT_BRIEF tag one can provide an optional one line description
 # for a project that appears at the top of each page and should give viewer a

Makefile

@@ -1,12 +1,21 @@
 ESPHOME_PATH = ../esphome
-ESPHOME_REF = 2024.3.1
+ESPHOME_REF = 2024.5.5
+PAGEFIND_VERSION=1.1.0
+PAGEFIND=pagefind
+NET_PAGEFIND=../pagefindbin/pagefind
 
-.PHONY: html html-strict cleanhtml deploy help live-html Makefile netlify netlify-api api netlify-dependencies svg2png copy-svg2png minify
+.PHONY: pagefind build-html html html-strict cleanhtml deploy help live-html live-pagefind Makefile netlify netlify-api api netlify-dependencies svg2png copy-svg2png minify
 
-html:
+html: pagefind
+	sphinx-build -M html . _build -j auto -n $(O) -Dhtml_extra_path=_redirects,_pagefind
+
+pagefind:
 	sphinx-build -M html . _build -j auto -n $(O)
-live-html:
-	sphinx-autobuild . _build -j auto -n $(O) --host 0.0.0.0
+	mkdir -p _pagefind/pagefind
+	${PAGEFIND}
+
+live-html:	pagefind
+	sphinx-autobuild . _build -j auto -n $(O) --host 0.0.0.0 -Dhtml_extra_path=_redirects,_pagefind
 
 html-strict:
 	sphinx-build -M html . _build -W -j auto -n $(O)
@@ -32,6 +41,12 @@ api:
 	fi
 	ESPHOME_PATH=$(ESPHOME_PATH) doxygen Doxygen
 
+net-html:
+	sphinx-build -M html . _build -j auto -n $(O)
+	mkdir -p _pagefind/pagefind
+	${NET_PAGEFIND}
+	sphinx-build -M html . _build -j auto -n $(O) -Dhtml_extra_path=_redirects,_pagefind
+
 netlify-api: netlify-dependencies
 	mkdir -p _build/html/api
 	@if [ ! -d "$(ESPHOME_PATH)" ]; then \
@@ -40,19 +55,31 @@ netlify-api: netlify-dependencies
 	fi
 	ESPHOME_PATH=$(ESPHOME_PATH) ../doxybin/doxygen Doxygen
 
-netlify-dependencies:
+netlify-dependencies: pagefind-binary
 	mkdir -p ../doxybin
 	curl -L https://github.com/esphome/esphome-docs/releases/download/v1.10.1/doxygen-1.8.13.xz | xz -d >../doxybin/doxygen
 	chmod +x ../doxybin/doxygen
 
+pagefind-binary:
+	mkdir -p ../pagefindbin
+	curl -o pagefind.tar.gz https://github.com/CloudCannon/pagefind/releases/download/v$(PAGEFIND_VERSION)/pagefind-v$(PAGEFIND_VERSION)-x86_64-unknown-linux-musl.tar.gz -L
+	tar xzf pagefind.tar.gz
+	rm pagefind.tar.gz
+	mv pagefind ${NET_PAGEFIND}
+
+
 copy-svg2png:
 	cp svg2png/*.png _build/html/_images/
 
-netlify: netlify-dependencies netlify-api html copy-svg2png
+netlify: netlify-dependencies netlify-api net-html copy-svg2png
 
 lint: html-strict
 	python3 lint.py
 
+clean:
+	rm -rf _pagefind/
+	sphinx-build -M clean . _build $(O)
+
 # Catch-all target: route all unknown targets to Sphinx using the new
 # "make mode" option.  $(O) is meant as a shortcut for $(SPHINXOPTS).
 %: Makefile

_static/browserconfig.xml

@@ -3,7 +3,7 @@
     <msapplication>
         <tile>
             <square150x150logo src="/_static/mstile-150x150.png"/>
-            <TileColor>#dfdfdf</TileColor>
+            <TileColor>#18bcf2</TileColor>
         </tile>
     </msapplication>
 </browserconfig>

_static/custom.css

@@ -1,3 +1,9 @@
+/* provide this to be queried in JS. Sadly can't be used in media-queries just yet*/
+
+:root {
+  --mobile-width-stop: 875;
+}
+
 .row-odd {
   background-color: #f3f6f6;
 }
@@ -240,9 +246,77 @@ a:hover code {
   background: none;
 }
 
+/* don't underline links that contain an image and nothing else */
+a:has(> img:only-child) {
+  border-bottom: none;
+}
+
 div.body p, div.body dd, div.body li, div.body blockquote {
   hyphens: none;
 }
+.pagefind-ui__form {
+    width: 100%;
+    max-width: 300px;
+    left: auto;
+    right: auto;
+    position: relative;
+}
+
+.pagefind-modular-list-excerpt, .pagefind-modular-list-title {
+    color: #111111 !important;
+}
+
+.search-results {
+    background-color: #f8f8f8;
+    box-shadow: 0 6px 10px rgb(0 0 0 / 0.2);
+    position: fixed;
+    z-index: 1500;
+    padding-right: 6px;
+    padding-left: 6px;
+    border-radius: 12px;
+    overflow: auto;
+    width: 0;
+    height: fit-content;
+    max-width: 650px;
+    transition: height, width 0.1s ease-in-out;
+    display: none;
+}
+
+/* New branding changes */
+
+div.body h1, div.body h2, div.body h3, div.body h4, div.body h5, div.body h6, div.sphinxsidebar h3, div.sphinxsidebar h4, div.admonition p.admonition-title {
+  font-family: Figtree, system, -apple-system, ".SFNSText-Regular", "San Francisco", "Roboto", "Segoe UI", "Helvetica Neue", "Lucida Grande", sans-serif;
+  font-weight: 600;
+}
+
+div.body h1 {
+  font-size: 2.5rem;
+}
+
+body {
+  font-family: "Instrument Sans", system, -apple-system, ".SFNSText-Regular", "San Francisco", "Roboto", "Segoe UI", "Helvetica Neue", "Lucida Grande", sans-serif;
+  line-height: 1.5;
+  letter-spacing: 0.01rem;
+}
+
+div.body p, div.body dd, div.body li {
+  line-height: 1.6;
+}
+
+@media screen and (max-width: 875px) {
+  /* hide search result thumbnails on mobile */
+  .pagefind-modular-list-thumb {
+    width: 0;
+  }
+  /* reduce height of search box */
+  .pagefind-modular-input-wrapper {
+    scale: 90%;
+  }
+  .logo {
+    scale: 60%;
+  }
+}
+
 
 /* dark theme */
 @media (prefers-color-scheme: dark) {
@@ -339,4 +413,25 @@ div.body p, div.body dd, div.body li, div.body blockquote {
     background-color: #8e8129;
   }
 
+  .search-results {
+    background-color: #313131;
+    box-shadow: 0 6px 10px rgb(0 0 0 / 0.8);
+  }
+  .pagefind-modular-list-excerpt, .pagefind-modular-list-title {
+      color: #eeeeee !important;
+  }
+
+  .pagefind-ui__form, .pagefind-modular-input, .search-results {
+    color: #ececec !important;
+  }
+
+  :root {
+    --pagefind-ui-primary: #eeeeee;
+    --pagefind-ui-text: #eeeeee;
+    --pagefind-ui-background: #152028;
+    --pagefind-ui-border: #152028;
+    --pagefind-ui-tag: #152028;
+  }
+
+
 }

_static/safari-pinned-tab.svg

@@ -1 +1,10 @@
-<svg version="1.0" xmlns="http://www.w3.org/2000/svg" width="1066.667" height="1066.667" viewBox="0 0 800 800"><path d="M266.5 149.6c-12.4 3.1-19.4 8.1-24.5 17.5l-3.5 6.4-.3 17.6-.4 17.6-4.3.6c-6.1.9-11.1 4.2-14.3 9.6l-2.7 4.6-.3 160.2L216 544H94v-15h49c34.4 0 49.6-.3 51.4-1.1 5-2.3 5.7-6.1 5.4-27.4l-.3-19.5-2.8-2.7-2.7-2.8-50-.3-50-.3V460h99l3.2-2.9 3.3-2.9V412l-2.8-2.7-2.7-2.8-50-.3-50-.3v-14.8l50-.3 50-.3 2.7-2.8 2.8-2.7v-42.2l-3.3-2.9-3.2-2.9H94v-99.8l-2.6-3.1c-3.6-4.3-9.3-4.4-13.5-.2l-2.9 2.9v113.4l2.9 2.9 2.9 2.9H180v16H80.8l-2.9 2.9-2.9 2.9v41.4l2.9 2.9 2.9 2.9H180v16H80.8l-2.9 2.9-2.9 2.9v41l2.6 3.1 2.6 3.1H180v16H81.1l-2.8 2.4-2.8 2.4-.3 21-.3 21 3 3.4 2.9 3.3 67.5.3 67.5.2.7 4.3c.4 2.3 1.3 5.3 2 6.7 2.8 5.4 10.1 10 15.9 10h3.5l.3 19.7c.3 19 .4 20 3 25.5 5.4 11.6 15.2 18.1 28.3 18.6 9.8.5 17.1-1.9 23.7-7.7 9.3-8.2 11.8-17 11.8-41.4V585h12v15.3c0 8.4.5 18 1.1 21.3 2.2 11.9 9.9 21.4 20.8 25.5 7.8 2.9 19.4 2.4 26.6-1.3 6.4-3.4 12.8-10 15.7-16.3 2.1-4.6 2.3-6.7 2.6-24.8l.4-19.7h12.6l.4 19.7c.3 17.7.6 20.3 2.5 24.5 2.9 6.3 9.7 13.4 15.8 16.6 7.2 3.7 18.8 4.2 26.6 1.3 7.9-3 14.1-8.8 18.1-16.9l3.3-6.7.3-19.3.4-19.3 6.1.3 6.2.3.5 20c.5 19.5.6 20.1 3.3 25.3 3.5 6.7 9 12.2 15.3 15.3 4.1 2 6.4 2.4 14.4 2.4 8.1 0 10.3-.4 14.5-2.4 6.3-3.2 12.4-9.3 15.6-15.6 2.2-4.7 2.4-6.3 2.9-25l.5-20 6.1-.3 6.2-.3.3 19.3.4 19.3 3.3 6.7c4 8.1 10.2 13.9 18.1 16.9 7.8 2.9 19.4 2.4 26.6-1.3 6.1-3.2 12.9-10.3 15.8-16.6 2-4.2 2.2-6.7 2.5-24.5l.4-19.7h12.6l.4 19.7c.3 22.6 1.3 26.1 9.1 34.1 6.4 6.7 12.7 9.5 22.2 10 9.8.5 17-1.9 23.7-7.7 9.2-8.2 11.8-17 11.8-41.2v-14.6l4.5-.5c5.4-.7 10.2-3.7 13.6-8.7l2.4-3.6.3-173c.2-121 0-174.1-.8-176.7-2.1-7.2-10.2-13.7-17.1-13.8h-2.6l-.5-16.9c-.4-16.6-.5-17-3.6-23.4-5.9-12-16.9-19-29.6-19-13.6 0-24.8 7-30.4 19.1-2.5 5.4-2.7 6.7-3 22.9l-.4 17.3H623v-15.3c0-17.2-1.1-22.4-6.1-30.1-6.5-9.7-20.5-15.8-31.9-13.8-11.9 2.1-20.7 8.9-25.7 19.7-2.6 5.6-2.7 7-3.1 22.7l-.4 16.8H543v-16.5c0-14.1-.3-17.2-2-21.9-2.9-7.6-8.8-13.9-16.6-17.7-5.7-2.8-7.6-3.3-14.4-3.3-6.8 0-8.7.5-14.4 3.3-7.1 3.5-12.2 8.6-15.8 16-2.1 4.2-2.3 6.3-2.6 22.3l-.4 17.8h-12.6l-.4-16.8c-.6-19.7-1.7-23.7-8.8-31.5-8.6-9.5-20.5-13.2-32.1-10.2-10.5 2.6-18.2 9-22.8 18.5-2.4 5.1-2.6 6.6-2.9 22.7l-.4 17.3H384v-15.3c0-17.2-1.1-22.4-6.1-30.1-6.5-9.7-20.5-15.8-31.9-13.8-11.9 2.1-20.7 9-25.8 20.1-2.4 5.1-2.6 7-3 22.3l-.5 16.8H305v-12.3c0-21.3-2.8-30.7-11.3-38.4-7-6.2-20-10.4-27.2-8.7zm11.5 20.9c1.5.8 3.8 3 4.9 4.8 1.9 3.1 2.1 4.9 2.1 18.6V209h-28v-13.9c0-7.7.5-15.2 1.1-16.8 1.3-3.4 4.7-7.2 7.4-8.3 3.2-1.4 9.4-1.1 12.5.5zm81.6 1.6c4.6 4.2 5.4 7.6 5.4 22.9v14h-28v-15c0-16.9.8-19.6 6.3-23.1 4.5-2.8 12.7-2.2 16.3 1.2zm77.5-1.6c6 3.1 6.9 6.3 6.9 23.2V209h-28.2l.4-15.3c.2-12.7.6-15.8 2.1-18 4-6.1 12.4-8.4 18.8-5.2zm80.4.5c5.5 3.4 6.5 6.9 6.5 23.4V209h-28v-14.6c0-13 .2-15 2.1-18.3 1.1-2.1 3.3-4.5 4.7-5.4 3.7-2.3 10.7-2.2 14.7.3zm81.5 1.5c4.1 4 5 7.9 5 23.2V209h-28v-15c0-16.9.8-19.6 6.3-23.1 4.8-3 12.7-2.2 16.7 1.6zm77.1-2c6 3.1 6.9 6.3 6.9 23.2V209h-28v-13.9c0-7.7.5-15.2 1.1-16.8 1.3-3.4 4.7-7.2 7.4-8.3 3.3-1.4 9.4-1.1 12.6.5zm26.7 226.7l-.3 166.3-232.2.3-232.3.2V231h465l-.2 166.2zM285 602.3c0 14.8-.3 17.7-1.8 20.6-3.7 6.8-12.9 9.1-19.3 4.8-6.1-4-6.9-7.1-6.9-26V585h28v17.3zm79.5.7c0 19.5-.5 21.2-6.8 25-6.4 3.9-15.4 1.5-18.9-5.1-1.5-2.9-1.8-5.8-1.8-20.7v-17.3l13.8.3 13.7.3V603zm79.5-.3c0 15.7-.2 18.2-1.9 20.9-3.7 6.1-13.4 8.1-19.6 4-5-3.3-6-6.8-6.3-23.9-.2-8.7-.1-16.4.2-17.2.4-1.2 3.2-1.5 14.1-1.5H444v17.7zm80-.5c0 15.5-.2 17.6-2 20.6-4.3 7-12.8 9.2-19.1 4.9-6.1-4-6.9-7.1-6.9-26V585h28v17.2zm79.5.8c0 19.5-.5 21.2-6.8 25-6.1 3.8-14.9 1.7-18.7-4.5-1.8-2.9-2-4.9-2-20.9v-17.7l13.8.3 13.7.3V603zm79.5-.7c0 14.8-.3 17.7-1.8 20.6-3.7 6.8-12.9 9.1-19.3 4.8-6-4-6.9-7.1-6.9-25.3 0-8.8.3-16.4.7-16.7.3-.4 6.6-.7 14-.7H683v17.3z"/><path d="M413.7 359.8c-39.5 39.5-53.7 54.3-53.7 56 0 3.5 2.8 8.1 5.3 8.7 1.2.3 6.3.6 11.2.8l9 .2.5 32.3.5 32.4 2.4 1.9c2.2 1.8 5.1 1.9 82.1 1.9s79.9-.1 82.1-1.9l2.4-1.9.5-32.4.5-32.3 9-.2c11.8-.4 13.2-.8 15-4.3 2.8-5.4 2.1-6.6-11.5-20.5l-13-13.2v-22.4c-.1-16-.4-22.9-1.3-24-2.4-3.1-5.6-3.9-15.7-3.9-9.9 0-10.2.1-13.1 2.9-2.4 2.5-2.9 3.7-2.9 8 0 2.8-.3 5.1-.8 5.1-.4 0-11.3-10.6-24.2-23.5-21.8-21.8-23.7-23.5-27-23.5-3.3 0-6.6 3.1-57.3 53.8z"/></svg>
+<svg width="512" height="512" viewBox="0 0 512 512" fill="none" xmlns="http://www.w3.org/2000/svg">
+<g clip-path="url(#clip0_2_408)">
+<path d="M372.68 238.9L267.32 133.52C261.1 127.3 250.92 127.3 244.7 133.52L139.32 238.9C133.1 245.12 128 257.42 128 266.22V362.22C128 371.02 135.2 378.22 144 378.22H206.94V218.92C206.94 215.38 209.8 212.52 213.34 212.52H298.68C302.22 212.52 305.08 215.38 305.08 218.92V244.52C305.08 248.06 302.22 250.92 298.68 250.92H245.34V263.72H298.68C302.22 263.72 305.08 266.58 305.08 270.12V295.72C305.08 299.26 302.22 302.12 298.68 302.12H245.34V314.92H298.68C302.22 314.92 305.08 317.78 305.08 321.32V346.92C305.08 350.46 302.22 353.32 298.68 353.32H238.94C235.4 353.32 232.54 350.46 232.54 346.92C232.54 343.38 235.4 340.52 238.94 340.52H292.28V327.72H238.94C235.4 327.72 232.54 324.86 232.54 321.32V295.72C232.54 292.18 235.4 289.32 238.94 289.32H292.28V276.52H238.94C235.4 276.52 232.54 273.66 232.54 270.12V244.52C232.54 240.98 235.4 238.12 238.94 238.12H292.28V225.32H219.74V378.22H368C376.8 378.22 384 371.02 384 362.22V266.22C384 257.42 378.9 245.12 372.68 238.9Z" fill="#F2F4F9"/>
+</g>
+<defs>
+<clipPath id="clip0_2_408">
+<rect width="256" height="256" fill="white" transform="translate(128 128.62)"/>
+</clipPath>
+</defs>
+</svg>

_static/site.webmanifest

@@ -33,8 +33,8 @@
             "type": "image/png"
         }
     ],
-    "theme_color": "#dfdfdf",
-    "background_color": "#dfdfdf",
+    "theme_color": "#18bcf2",
+    "background_color": "#18bcf2",
     "start_url": "https://esphome.io/",
     "display": "standalone"
 }

_static/version

@@ -1 +1 @@
-2024.3.1
+2024.5.5

_templates/layout.html

@@ -5,6 +5,7 @@
 {% endblock %}
 
 {%- block extrahead %}
+  <link href="/pagefind/pagefind-modular-ui.css" rel="stylesheet">
   <link rel="stylesheet" href="{{ pathto('_static/custom.css', 1) }}?hash={{ custom_css_hash }}" type="text/css" />
   <link rel="apple-touch-icon" sizes="180x180" href="/_static/apple-touch-icon.png">
   <link rel="shortcut icon" href="/_static/favicon.ico">
@@ -15,27 +16,30 @@
   <link rel="icon" type="image/png" sizes="32x32" href="/_static/favicon-32x32.png">
   <link rel="icon" type="image/png" sizes="16x16" href="/_static/favicon-16x16.png">
   <link rel="manifest" href="/_static/site.webmanifest">
-  <link rel="mask-icon" href="/_static/safari-pinned-tab.svg" color="#646464">
+  <link rel="mask-icon" href="/_static/safari-pinned-tab.svg" color="#18bcf2">
+  <link rel="me" href="https://fosstodon.org/@esphome">
   <meta name="apple-mobile-web-app-title" content="ESPHome">
   <meta name="application-name" content="ESPHome">
-  <meta name="msapplication-TileColor" content="#dfdfdf">
+  <meta name="msapplication-TileColor" content="#18bcf2">
   <meta name="msapplication-config" content="/_static/browserconfig.xml">
-  <meta name="theme-color" content="#dfdfdf">
+  <meta name="theme-color" content="#18bcf2">
   <meta name="HandheldFriendly" content="True">
   <meta name="MobileOptimized" content="320">
   <meta property="og:site_name" content="ESPHome">
-  <meta name="viewport" content="width=device-width, initial-scale=0.9, maximum-scale=0.9">
+  <meta name="viewport"
+        content="width=device-width, initial-scale=1, maximum-scale=3, interactive-widget=overlays-content">
 {% endblock %}
 
 {% block relbar_top %}
-  {% if parents|length > 0 %}
   <ul class="breadcrumbs">
+  {% if parents|length > 0 %}
     {%- for doc in parents %}
       <li><a href="{{ doc.link|e }}">{{ doc.title }}</a> ➔</li>
     {%- endfor %}
       <li>{{title}}</li>
-  </ul>
+
   {% endif %}
+  </ul>
 {% endblock %}
 
 {% block footer %}

_templates/search.html

@@ -0,0 +1,36 @@
+<!-- docs/_templates/search.html -->
+{% extends "page.html" %}
+
+{%- block htmltitle -%}
+<title>{{ _("Search") }} - {{ docstitle }}</title>
+{%- endblock htmltitle -%}
+
+{% block content %}
+<h1>{{ _("Search") }}</h1>
+<div id="search"></div>
+{% endblock %}
+
+{% block scripts -%}
+{{ super() }}
+{%- endblock scripts %}
+
+{% block extra_styles -%}
+{{ super() }}
+  <style type="text/css">
+    #search form input[type="text"] {
+      box-sizing: border-box;
+      width: 100%;
+      line-height: 2em;
+      padding-inline: 0.6em;
+      font-size: 1.2rem;
+      border-radius: 0.05rem;
+      border: 2px solid var(--color-foreground-border);
+      border-bottom-color: 2px solid var(--color-foreground-secondary);
+      transition: border-color 20ms ease;
+    }
+    #search form input[type="text"]:focus {
+      border-color: var(--color-foreground-primary);
+    }
+  </style>
+{%- endblock extra_styles %}
+

_templates/searchbox.html

@@ -0,0 +1,188 @@
+<script src="/pagefind/pagefind-modular-ui.js"></script>
+<div class="pagefind-ui__form" id="search"></div>
+<script>
+
+
+    class El {
+        constructor(tagname) {
+            this.element = document.createElement(tagname);
+        }
+
+        id(s) {
+            this.element.id = s;
+            return this;
+        }
+
+        class(s) {
+            this.element.classList.add(s);
+            return this;
+        }
+
+        attrs(obj) {
+            for (const [k,v] of Object.entries(obj)) {
+                this.element.setAttribute(k, v);
+            }
+            return this;
+        }
+
+        text(t) {
+            this.element.innerText = t;
+            return this;
+        }
+
+        html(t) {
+            this.element.innerHTML = t;
+            return this;
+        }
+
+        handle(e, f) {
+            this.element.addEventListener(e, f);
+            return this;
+        }
+
+        addTo(el) {
+            if (el instanceof El) {
+                el.element.appendChild(this.element);
+            } else {
+                el.appendChild(this.element);
+            }
+            return this.element;
+        }
+    }
+
+    window.addEventListener('DOMContentLoaded', (event) => {
+
+        const targetClass = "search-results";
+        const docel = document.getElementsByClassName("document");
+        if (docel.length === 0)
+            return;
+        const inpel = document.getElementById("search");
+        if (!inpel)
+            return;
+
+        var mobileWidth = getComputedStyle(document.body).getPropertyValue("--mobile-width-stop");
+
+        function isMobile() {
+            return window.innerWidth <= mobileWidth;
+        }
+
+        const target = document.createElement("div");
+        target.classList.add(targetClass);
+        target.id = targetClass;
+        target.style.display = "none";
+        docel.item(0).appendChild(target);
+
+        const margin = 20;
+
+        const resultTemplate = (result) => {
+            let wrapper = new El("li").class("pagefind-modular-list-result");
+
+            let thumb = new El("div").class("pagefind-modular-list-thumb").addTo(wrapper);
+            if (result?.meta?.image) {
+                new El("img").class("pagefind-modular-list-image").attrs({
+                    src: result.meta.image,
+                    alt: result.meta.image_alt || result.meta.title
+                }).addTo(thumb);
+            }
+
+            let inner = new El("div").class("pagefind-modular-list-inner").addTo(wrapper);
+            let title = new El("p").class("pagefind-modular-list-title").addTo(inner);
+            new El("a").class("pagefind-modular-list-link").text(result.meta?.title).attrs({
+                href: result.meta?.url || result.url
+            }).addTo(title);
+
+            let excerpt = new El("p").class("pagefind-modular-list-excerpt").addTo(inner);
+            new El("a").class("pagefind-modular-list-link").html(result.excerpt).attrs({
+                href: result.meta?.url || result.url
+            }).addTo(excerpt);
+
+            return wrapper.element;
+        }
+
+
+        function resizeTarget() {
+            const searchPos = inpel.getBoundingClientRect();
+            var leftPos;
+            var topPos;
+            var maxWidth = 650;
+            target.style.width = "auto;"
+            target.style.height = "fit-content";
+            target.style.maxWidth = maxWidth + "px";
+            let rightPos = margin;
+            if (isMobile()) {
+                // position search results left aligned with the search box, and below.
+                leftPos = margin / 2;
+                topPos = searchPos.bottom + margin / 2;
+                rightPos = margin / 2;
+            } else {
+                // position search results top aligned with the search box, and to its right.
+                leftPos = searchPos.right + margin * 2;
+                topPos = searchPos.top;
+                if (rightPos - leftPos > maxWidth)
+                    rightPos = leftPos + maxWidth;
+            }
+            target.style.right = rightPos + "px";
+            target.style.top = topPos + "px";
+            target.style.left = leftPos + "px";
+            let twidth = window.innerWidth - margin - leftPos;
+            if (twidth > maxWidth)
+                twidth = maxWidth;
+            target.style.width = twidth + "px";
+            target.style.maxHeight = (window.innerHeight - margin - topPos) + "px";
+        }
+
+        window.addEventListener("resize", (event) => { resizeTarget(); });
+
+        function showTarget() {
+            if (target.style.display !== "block") {
+                target.style.display = "block";
+                document.addEventListener('click', clickCallback);
+            }
+            resizeTarget();
+        }
+
+        function hideTargets() {
+            if (target.style.display !== "none") {
+                target.style.display = "none";
+                document.removeEventListener('click', clickCallback);
+            }
+        }
+
+
+        const instance = new PagefindModularUI.Instance({
+            showSubResults: true,
+            showImages: false,
+            ranking: {
+                pageLength: 0.0,
+                termSaturation: 1.6,
+                termFrequency: 0.4,
+                termSimilarity: 6.0
+            }
+        });
+
+        instance.add(new PagefindModularUI.Input({
+            containerElement: "#search"
+        }));
+
+        instance.add(new PagefindModularUI.ResultList({
+            containerElement: "#search-results",
+            resultTemplate: resultTemplate
+        }));
+
+        const clickCallback = (event) => {
+            const path = event.composedPath();
+            if (path.includes(target) || path.includes(inpel))
+                return;
+            hideTargets();
+        };
+        if (target) {
+            instance.on("results", (results) => {
+                if (results.results.length) {
+                    showTarget();
+                } else {
+                    hideTargets();
+                }
+            });
+        }
+    });
+</script>

changelog/2023.12.0.rst

@@ -14,7 +14,7 @@ ESPHome 2023.12.0 - 20th December 2023
     GT911, components/touchscreen/gt911, esp32_s3_box_3.png
     Pylontech Batteries, components/pylontech, pylontech.jpg
     HE60R Cover, components/cover/he60r, he60r.jpg
-    Graphical Display Menu, components/display_menu/graphical_display_menu, graphical_display_menu.jpg
+    Graphical Display Menu, components/display_menu/graphical_display_menu, graphical_display_menu.png
     FT63X6, components/touchscreen/ft63x6, wt32-sc01.png
     A02YYUW, components/sensor/a02yyuw, a02yyuw.jpg
     PN7150, components/binary_sensor/pn7150, pn7150.jpg

changelog/2024.3.0.rst

@@ -68,6 +68,12 @@ Release 2024.3.1 - March 27
 - Don't compile strptime unless its required :esphomepr:`6424` by :ghuser:`gabest11`
 - Fix editor live validation :esphomepr:`6431` by :ghuser:`bdraco`
 
+Release 2024.3.2 - April 4
+--------------------------
+
+- Fix logger compile error on ESP32-C6 :esphomepr:`6323` by :ghuser:`DAVe3283`
+- Add missing ethernet types :esphomepr:`6444` by :ghuser:`ssieb`
+- fix: changing the content source when playing is paused blocks the player :esphomepr:`6454` by :ghuser:`NewoPL`
 
 Thank you for your support
 --------------------------

changelog/2024.4.0.rst

@@ -0,0 +1,231 @@
+ESPHome 2024.4.0 - 17th April 2024
+==================================
+
+.. seo::
+    :description: Changelog for ESPHome 2024.4.0.
+    :image: /_static/changelog-2024.4.0.png
+    :author: Jesse Hills
+    :author_twitter: @jesserockz
+
+.. imgtable::
+    :columns: 4
+
+    Template Datetime Time, components/datetime/template, description.svg, dark-invert
+    SUN-GTIL2 inverter, components/sun_gtil2, sun_1000g2.png
+    AT581X, components/at581x, at581x.png
+    JSN-SR04T, components/sensor/jsn_sr04t, jsn-sr04t-v3.jpg
+
+    Daikin ARC, components/climate/climate_ir, air-conditioner-ir.svg, dark-invert
+    HHCCJCY10 (MiFlora Pink), components/sensor/xiaomi_hhccjcy10, xiaomi_hhccjcy10.jpg
+    TLC5971, components/output/tlc5971, tlc5971.jpg
+    Dooya, components/remote_transmitter, remote.svg
+
+
+Time Entities
+-------------
+
+ESPHome now has support for ``time`` entities that can be set from the frontend (like Home Assistant). THis allows you to set a timer to execute future automations on device.
+
+ESPHome Dates require Home Assistant 2024.4 or later.
+
+
+Voice Assistant Audio
+---------------------
+
+This release adds support for sending and receiving audio to/from voice assistants via the API. Currently ESPHome sends and receives the Voice Assistant audio bytes
+via a UDP socket which can be unreliable and insecure. Beginning with Home Assistant 2024.5, both sides will automatically recognise that they both support API Audio and will
+use that route instead. This is more reliable because the ESPHome API uses a TCP socket, so packet order and delivery is guaranteed, and if you use API Encryption,
+your audio will also be encrypted in transit.
+
+
+Release 2024.4.1 - April 23
+---------------------------
+
+- [Tuya Climate] Fix compilation error caused by codegen :esphomepr:`6568` by :ghuser:`zry98`
+- wifi: fix reconnect issue due to enablement of fast connect :esphomepr:`6598` by :ghuser:`jpeletier`
+- Calibrate Beken internal temperature :esphomepr:`6599` by :ghuser:`Mat931`
+- fix streaming logs from MQTT for ESP32 devices using TLS :esphomepr:`6605` by :ghuser:`ccutrer`
+- Disallow variant/family override for known boards :esphomepr:`6512` by :ghuser:`clydebarrow`
+- esp32_ble: Consider ESP_BT_STATUS_DONE a successful state :esphomepr:`6493` by :ghuser:`polyfloyd`
+- Fix or filter :esphomepr:`6574` by :ghuser:`swoboda1337`
+
+
+Release 2024.4.2 - April 30
+---------------------------
+
+- Fix SHT3xd fails sometimes in 2024.4.0 :esphomepr:`6592` by :ghuser:`mrtoy-me`
+- allow defaults with no include vars :esphomepr:`6613` by :ghuser:`ssieb`
+- Revert #6458 :esphomepr:`6650` by :ghuser:`tronikos`
+- [i2s_audio.microphone] Fixing adc bug :esphomepr:`6654` by :ghuser:`jesserockz`
+
+
+Full list of changes
+--------------------
+
+New Components
+^^^^^^^^^^^^^^
+
+- Add sun_gtil2 component (for SUN-1000G2 / SUN-2000G2 grid tie inverters) :esphomepr:`4958` by :ghuser:`Mat931` (new-integration)
+- Add support for AT581x component :esphomepr:`6297` by :ghuser:`X-Ryl669` (new-integration)
+- Add new Component: Ultrasonic Distance Sensor JSN-SR04T :esphomepr:`6023` by :ghuser:`Mafus1` (new-integration)
+- feat: Add Daikin ARC (tested on Daikin ARC472A62) :esphomepr:`6429` by :ghuser:`magicbear` (new-integration)
+- add support for Tuya pink version of miflora :esphomepr:`5402` by :ghuser:`fariouche` (new-integration)
+- Implemented support for the TLC5971 as an output component :esphomepr:`6494` by :ghuser:`IJIJI` (new-integration)
+
+Breaking Changes
+^^^^^^^^^^^^^^^^
+
+- Add support for new modes in Tuya Climate :esphomepr:`5159` by :ghuser:`moriahmorgan` (breaking-change)
+- IPv6 string representation follows RFC5952 :esphomepr:`6449` by :ghuser:`HeMan` (breaking-change)
+
+Beta Changes
+^^^^^^^^^^^^
+
+- Add dooya remote transmitter test :esphomepr:`6508` by :ghuser:`jesserockz`
+- ads1115: remove auto-load and split sensor into platform folder :esphomepr:`5981` by :ghuser:`jesserockz` (new-platform)
+- Bump esphome-dashboard to 20240412.0 :esphomepr:`6517` by :ghuser:`jesserockz`
+- Fix missing ifdefs in voice assistant :esphomepr:`6520` by :ghuser:`jesserockz`
+- Fix project version longer than 30 characters breaking compilation :esphomepr:`6535` by :ghuser:`jesserockz`
+- Fix no-release bug on ft6x36 :esphomepr:`6527` by :ghuser:`clydebarrow`
+
+All changes
+^^^^^^^^^^^
+
+- Bump docker/login-action from 3.0.0 to 3.1.0 :esphomepr:`6367` by :ghuser:`dependabot[bot]`
+- Bump peter-evans/create-pull-request from 6.0.1 to 6.0.2 :esphomepr:`6361` by :ghuser:`dependabot[bot]`
+- Bump docker/build-push-action from 5.2.0 to 5.3.0 in /.github/actions/build-image :esphomepr:`6373` by :ghuser:`dependabot[bot]`
+- Bump docker/setup-buildx-action from 3.1.0 to 3.2.0 :esphomepr:`6372` by :ghuser:`dependabot[bot]`
+- Fix deep_sleep for ESP32-C6 :esphomepr:`6377` by :ghuser:`ferrets6`
+- Fix keeloq for IDF 5+ :esphomepr:`6382` by :ghuser:`kbx81`
+- Fix Nextion set_component_picture call :esphomepr:`6378` by :ghuser:`edwardtfn`
+- Add line_at_angle method to Display component :esphomepr:`6381` by :ghuser:`deisterhold`
+- Check generated proto files are as expected if any are modified in PRs :esphomepr:`6254` by :ghuser:`jesserockz`
+- ld2420: fix energy mode documentation :esphomepr:`6225` by :ghuser:`andresv`
+- Add actions for component tests A, B and C :esphomepr:`6256` by :ghuser:`kbx81`
+- Add some components to the new testing framework (V) :esphomepr:`6231` by :ghuser:`kbx81`
+- Add some components to the new testing framework (X,Y,Z) :esphomepr:`6233` by :ghuser:`kbx81`
+- Add some components to the new testing framework (E) :esphomepr:`6176` by :ghuser:`kbx81`
+- Make SPI compile with IDF >= 5.0 :esphomepr:`6383` by :ghuser:`HeMan`
+- Fix esp32-camera test yaml :esphomepr:`6398` by :ghuser:`kbx81`
+- Bump pytest-asyncio from 0.23.5.post1 to 0.23.6 :esphomepr:`6402` by :ghuser:`dependabot[bot]`
+- Bump actions/cache from 4.0.1 to 4.0.2 in /.github/actions/restore-python :esphomepr:`6403` by :ghuser:`dependabot[bot]`
+- Bump actions/cache from 4.0.1 to 4.0.2 :esphomepr:`6404` by :ghuser:`dependabot[bot]`
+- Bump ESP8266 Arduino versions :esphomepr:`5359` by :ghuser:`HeMan`
+- Allow accept/reject delta to be specified. :esphomepr:`5060` by :ghuser:`cvwillegen`
+- Allow setting htop for ledc :esphomepr:`6340` by :ghuser:`Gagootron`
+- sm2135: add separate_modes option to support different chip variants :esphomepr:`6152` by :ghuser:`jasperro`
+- AHT10: fix temperature-only operation; add warning/error messages :esphomepr:`6405` by :ghuser:`clydebarrow`
+- Add support for new modes in Tuya Climate :esphomepr:`5159` by :ghuser:`moriahmorgan` (breaking-change)
+- Add sun_gtil2 component (for SUN-1000G2 / SUN-2000G2 grid tie inverters) :esphomepr:`4958` by :ghuser:`Mat931` (new-integration)
+- SPI: Make some validation failures give more useful messages. :esphomepr:`6413` by :ghuser:`clydebarrow`
+- Bump aioesphomeapi from 23.1.1 to 23.2.0 :esphomepr:`6412` by :ghuser:`dependabot[bot]`
+- Add check for use of GPIOXX in config :esphomepr:`6419` by :ghuser:`clydebarrow`
+- WireGuard for esp8266 :esphomepr:`6365` by :ghuser:`droscy`
+- setup.cfg: drop duplicate, underintended trove classifier :esphomepr:`6421` by :ghuser:`mweinelt`
+- Store preferences in disk file on host platform :esphomepr:`6428` by :ghuser:`clydebarrow`
+- Add support for AT581x component :esphomepr:`6297` by :ghuser:`X-Ryl669` (new-integration)
+- Add some components to the new testing framework (F) :esphomepr:`6177` by :ghuser:`kbx81`
+- Add get_contrast() and get_brightness() to SSD1306 class to get protected variables :esphomepr:`6435` by :ghuser:`benediktkr`
+- Add new Component: Ultrasonic Distance Sensor JSN-SR04T :esphomepr:`6023` by :ghuser:`Mafus1` (new-integration)
+- Add some components to the new testing framework (G) :esphomepr:`6178` by :ghuser:`kbx81`
+- Add some components to the new testing framework (K) :esphomepr:`6186` by :ghuser:`kbx81`
+- Add some components to the new testing framework (N) :esphomepr:`6210` by :ghuser:`kbx81`
+- Add some components to the new testing framework (Q) :esphomepr:`6218` by :ghuser:`kbx81`
+- Add some components to the new testing framework (U) :esphomepr:`6230` by :ghuser:`kbx81`
+- Fix spacing in new test yaml :esphomepr:`6441` by :ghuser:`kbx81`
+- Add some components to the new testing framework (W) :esphomepr:`6232` by :ghuser:`kbx81`
+- Add some components to the new testing framework (L) :esphomepr:`6195` by :ghuser:`kbx81`
+- feat: Add Daikin ARC (tested on Daikin ARC472A62) :esphomepr:`6429` by :ghuser:`magicbear` (new-integration)
+- Disable truthy yamllint rule :esphomepr:`6442` by :ghuser:`jesserockz`
+- Add get_size method to QR Code header :esphomepr:`6430` by :ghuser:`deisterhold`
+- Minor change to support sht85 sensor :esphomepr:`6415` by :ghuser:`mrtoy-me`
+- IPv6 string representation follows RFC5952 :esphomepr:`6449` by :ghuser:`HeMan` (breaking-change)
+- Bump actions/setup-python from 5.0.0 to 5.1.0 :esphomepr:`6437` by :ghuser:`dependabot[bot]`
+- Bump actions/setup-python from 5.0.0 to 5.1.0 in /.github/actions/restore-python :esphomepr:`6438` by :ghuser:`dependabot[bot]`
+- Optimize QMC5883L: Read registers only for enabled sensors :esphomepr:`6458` by :ghuser:`tronikos`
+- minor refactor to allow commit hash as ref value. :esphomepr:`6446` by :ghuser:`LelandSindt`
+- TMP117 fix polling period config :esphomepr:`6452` by :ghuser:`mrtoy-me`
+- Bump Arduino Pico Framework to 3.7.2 and Platform to 1.12.0 :esphomepr:`6386` by :ghuser:`HeMan`
+- Display menu: Allow "left" key to exit current menu if not editing :esphomepr:`6460` by :ghuser:`jesserockz`
+- Fix NOLINT on inclusive-language check :esphomepr:`6464` by :ghuser:`jesserockz`
+- Add yamllint to dev requirements :esphomepr:`6466` by :ghuser:`jesserockz`
+- Add temperature for QMC5883L :esphomepr:`6456` by :ghuser:`tronikos`
+- web_server: Return early if no clients connected :esphomepr:`6467` by :ghuser:`jesserockz`
+- ESP32 Arduino WiFi: misc bug fixes :esphomepr:`6470` by :ghuser:`paravoid`
+- Replace std::regex with sscanf calls :esphomepr:`6468` by :ghuser:`jesserockz`
+- Include "Failed" status in config log. :esphomepr:`6482` by :ghuser:`clydebarrow`
+- Fix Microphone IsCapturingCondition :esphomepr:`6490` by :ghuser:`RaymiiOrg`
+- Remove misleading tag/line in messages :esphomepr:`6495` by :ghuser:`clydebarrow`
+- Send/Receive Voice Assistant audio via API :esphomepr:`6471` by :ghuser:`jesserockz`
+- Datetime date initial value fix :esphomepr:`6483` by :ghuser:`RFDarter`
+- If the loop() took more than the required time, don't delay further :esphomepr:`6496` by :ghuser:`clydebarrow`
+- Bump LibreTiny version to 1.5.1 :esphomepr:`6500` by :ghuser:`kuba2k2`
+- Internal temperature: Support Beken platform :esphomepr:`6491` by :ghuser:`Mat931`
+- Bump docker/setup-buildx-action from 3.2.0 to 3.3.0 :esphomepr:`6502` by :ghuser:`dependabot[bot]`
+- add support for Tuya pink version of miflora :esphomepr:`5402` by :ghuser:`fariouche` (new-integration)
+- Add MAC address to WiFi config reply :esphomepr:`6489` by :ghuser:`cvwillegen`
+- Adds i2c timeout config :esphomepr:`4614` by :ghuser:`tracestep`
+- Add ABB-Welcome / Busch-Welcome Door Intercom Protocol :esphomepr:`4689` by :ghuser:`Mat931`
+- Add support for time entities :esphomepr:`6399` by :ghuser:`jesserockz`
+- Fix Match by IRK :esphomepr:`6499` by :ghuser:`MRemy2`
+- Add rmt_channel to remote_transmitter and remote_receiver :esphomepr:`6497` by :ghuser:`jesserockz` (new-integration)
+- Rework tlc5947 to remove AUTO_LOAD :esphomepr:`6503` by :ghuser:`jesserockz`
+- UART: ignore require_tx/rx if not a native uart implementation :esphomepr:`6504` by :ghuser:`jesserockz`
+- esp32_rmt_led_strip bugfixes :esphomepr:`6506` by :ghuser:`Mat931`
+- Implemented support for the TLC5971 as an output component :esphomepr:`6494` by :ghuser:`IJIJI` (new-integration)
+- Add Dooya protocol to remote_base :esphomepr:`6488` by :ghuser:`bukureckid`
+- Only give error for connected sensors at startup :esphomepr:`6474` by :ghuser:`leejoow`
+- Webserver float to string fix :esphomepr:`6507` by :ghuser:`RFDarter`
+- Add dooya remote transmitter test :esphomepr:`6508` by :ghuser:`jesserockz`
+- ads1115: remove auto-load and split sensor into platform folder :esphomepr:`5981` by :ghuser:`jesserockz` (new-platform)
+- Bump esphome-dashboard to 20240412.0 :esphomepr:`6517` by :ghuser:`jesserockz`
+- Fix missing ifdefs in voice assistant :esphomepr:`6520` by :ghuser:`jesserockz`
+- Fix project version longer than 30 characters breaking compilation :esphomepr:`6535` by :ghuser:`jesserockz`
+- Fix no-release bug on ft6x36 :esphomepr:`6527` by :ghuser:`clydebarrow`
+
+Past Changelogs
+---------------
+
+- :doc:`2024.3.0`
+- :doc:`2024.2.0`
+- :doc:`2023.12.0`
+- :doc:`2023.11.0`
+- :doc:`2023.10.0`
+- :doc:`2023.9.0`
+- :doc:`2023.8.0`
+- :doc:`2023.7.0`
+- :doc:`2023.6.0`
+- :doc:`2023.5.0`
+- :doc:`2023.4.0`
+- :doc:`2023.3.0`
+- :doc:`2023.2.0`
+- :doc:`2022.12.0`
+- :doc:`2022.11.0`
+- :doc:`2022.10.0`
+- :doc:`2022.9.0`
+- :doc:`2022.8.0`
+- :doc:`2022.6.0`
+- :doc:`2022.5.0`
+- :doc:`2022.4.0`
+- :doc:`2022.3.0`
+- :doc:`2022.2.0`
+- :doc:`2022.1.0`
+- :doc:`2021.12.0`
+- :doc:`2021.11.0`
+- :doc:`2021.10.0`
+- :doc:`2021.9.0`
+- :doc:`2021.8.0`
+- :doc:`v1.20.0`
+- :doc:`v1.19.0`
+- :doc:`v1.18.0`
+- :doc:`v1.17.0`
+- :doc:`v1.16.0`
+- :doc:`v1.15.0`
+- :doc:`v1.14.0`
+- :doc:`v1.13.0`
+- :doc:`v1.12.0`
+- :doc:`v1.11.0`
+- :doc:`v1.10.0`
+- :doc:`v1.9.0`
+- :doc:`v1.8.0`
+- :doc:`v1.7.0`

changelog/2024.5.0.rst

@@ -0,0 +1,327 @@
+ESPHome 2024.5.0 - 15th May 2024
+================================
+
+.. seo::
+    :description: Changelog for ESPHome 2024.5.0.
+    :image: /_static/changelog-2024.5.0.png
+    :author: Jesse Hills
+    :author_twitter: @jesserockz
+
+.. imgtable::
+    :columns: 3
+
+
+    Valve Core, components/valve/index, folder-open.svg, dark-invert
+    Template Valve, components/valve/template, description.svg, dark-invert
+    Event Core, components/event/index, folder-open.svg, dark-invert
+    Template Event, components/event/template, description.svg, dark-invert
+    Template Time, components/datetime/template, description.svg, dark-invert
+    Template Datetime, components/datetime/template, description.svg, dark-invert
+    WeiKai SPI/I²C UART/IO Expander, components/weikai, wk2168.jpg
+
+
+Valves, Events, and More
+------------------------
+
+This release brings a new ``Valve`` component, which can be used to control valves.
+A ``Valve`` can be opened, closed, or a specific position set if supported.
+
+``Event`` entities were added to Home Assistant in `2023.8 <https://www.home-assistant.io/blog/2023/08/02/release-20238/#introducing-the-event-entity>`__.
+They allow better structure and also history and logging of the events sent from ESPHome to Home Assistant compared to just using publishing events onto the
+Home Assistant event bus with the ``homeassistant.event`` action.
+
+The ``datetime`` component has also been extended with ``DateTime`` and ``Time`` entity types this release.
+
+
+ESP32 ADC Attenuation
+---------------------
+
+The attenuation configuration option for ESP32 ``adc`` sensors has had a deprecation in the underlying ESP-IDF framework with the ``11dB`` option.
+The value to replace ``11dB`` with is ``12dB``. There are no functionality changes otherwise. There will be a warning in the logs when installing if you
+are using ``11dB`` and it will be removed in **2024.8.0**.
+
+Remote Receiver tolerance
+-------------------------
+
+The ``tolerance`` option in the ``remote_receiver`` component has been extended to allow time values, but at the same time the validation is now more strict.
+If you were using a raw value with no unit before 2024.5.0, for example ``25``, you will need to change it to ``25%``.
+
+
+Release 2024.5.1 - May 20
+-------------------------
+
+- Add device_class to valve core config :esphomepr:`6765` by :ghuser:`acshef`
+- Synchronise Device Classes from Home Assistant :esphomepr:`6768` by :ghuser:`esphomebot`
+- Fix Upload from Dashboard with MQTT discovery. :esphomepr:`6774` by :ghuser:`Links2004`
+- Fix MQTT dashboard discovery (Exception in MqttStatusThread). :esphomepr:`6775` by :ghuser:`Links2004`
+
+
+Release 2024.5.2 - May 21
+-------------------------
+
+- Revert "Fix MQTT dashboard discovery (Exception in MqttStatusThread)." :esphomepr:`6782` by :ghuser:`bdraco`
+- Fix DashboardEntries.all() call :esphomepr:`6783` by :ghuser:`bdraco`
+- [remote_receiver] Add better error message for tolerance breaking change :esphomepr:`6784` by :ghuser:`jesserockz`
+- Update webserver local assets to 20240519-215627 :esphomepr:`6779` by :ghuser:`esphomebot`
+
+
+Release 2024.5.3 - May 25
+-------------------------
+
+- [voice_assistant] Don't allocate buffers until starting the microphone for the first time :esphomepr:`6800` by :ghuser:`jesserockz`
+
+
+Release 2024.5.4 - May 28
+-------------------------
+
+- [web_server_base] Bump ESPAsyncWebServer-esphome to 3.2.2 :esphomepr:`6797` by :ghuser:`jesserockz`
+- [helpers] Move Base64 string to cpp :esphomepr:`6819` by :ghuser:`gabest11`
+
+
+Release 2024.5.5 - June 5
+-------------------------
+
+- [voice_assistant] Half the microphone ringbuffer size :esphomepr:`6830` by :ghuser:`jesserockz`
+- [i2s_speaker] Add buffer allocation failure checks :esphomepr:`6829` by :ghuser:`jesserockz`
+- [improv_serial] Fix for IDF 4.4.7 :esphomepr:`6855` by :ghuser:`kbx81`
+
+
+Full list of changes
+--------------------
+
+New Components
+^^^^^^^^^^^^^^
+
+- Add valve component :esphomepr:`6447` by :ghuser:`kbx81` (new-integration)
+- Add the WeiKai SPI/I2C UART/IO Expander components to esphome  :esphomepr:`5218` by :ghuser:`DrCoolzic` (new-integration)
+- Event entity support :esphomepr:`6451` by :ghuser:`nohat` (new-integration)
+- SPI and I2C for BMP390 and BMP380 :esphomepr:`6652` by :ghuser:`latonita` (new-integration) (breaking-change)
+
+Breaking Changes
+^^^^^^^^^^^^^^^^
+
+- Add DNS sensor and simplify format :esphomepr:`6450` by :ghuser:`HeMan` (breaking-change)
+- SM2135 - Use standard channel ordering. :esphomepr:`6573` by :ghuser:`Cossid` (breaking-change)
+- [sn74hc595] Enforce type field to distinguish gpio vs spi mode :esphomepr:`6609` by :ghuser:`jesserockz` (breaking-change)
+- Add datetime entities :esphomepr:`6513` by :ghuser:`jesserockz` (breaking-change)
+- SPI and I2C for BMP390 and BMP380 :esphomepr:`6652` by :ghuser:`latonita` (new-integration) (breaking-change)
+
+Beta Changes
+^^^^^^^^^^^^
+
+- [github] Upgrade to actions/[upload,download]-artifact v4 :esphomepr:`6698` by :ghuser:`jesserockz`
+- [nextion] Replace flags to ``USE_ARDUINO`` :esphomepr:`6700` by :ghuser:`edwardtfn`
+- [remote_receiver, remote_transmitter] Improve error messages on the ESP32 :esphomepr:`6701` by :ghuser:`Mat931`
+- [ethernet] Use constexpr instead of inline define for KSZ80XX_PC2R_REG_ADDR :esphomepr:`6705` by :ghuser:`jesserockz`
+- Add PHY register writes to enable external clock on Ethernet with RTL8201 :esphomepr:`6704` by :ghuser:`heythisisnate`
+- Bump recommended ESP-IDF to 4.4.7 :esphomepr:`6703` by :ghuser:`bdraco`
+- [core] Ensure that a generated ID name is distinct from its type. :esphomepr:`6706` by :ghuser:`clydebarrow`
+- [color] Fix crash when hex color parses as int, improve error reporting. :esphomepr:`6707` by :ghuser:`clydebarrow`
+- [github] Fix digest artifact name :esphomepr:`6710` by :ghuser:`jesserockz`
+- fix(ltr390): stuck ALS values when configured for ALS+UV readings :esphomepr:`6723` by :ghuser:`CodeInPolish`
+- Set FEATURE_API_AUDIO flag also if the speaker component is not used :esphomepr:`6712` by :ghuser:`gnumpi`
+- Bump platformio from 6.1.13 to 6.1.15 :esphomepr:`6634` by :ghuser:`dependabot[bot]`
+- Fix ESPHOME_PROJECT_VERSION_30 :esphomepr:`6731` by :ghuser:`jesserockz`
+- Voice-Assistant: Start-order change for VAD disabled: start va-pipeline when microphon… :esphomepr:`6391` by :ghuser:`gnumpi`
+- Add ANNOUNCING state to media_player. :esphomepr:`6691` by :ghuser:`gnumpi`
+- [adc] Fix 11db deprecation warning :esphomepr:`6749` by :ghuser:`jesserockz` (notable-change)
+
+Notable Changes
+^^^^^^^^^^^^^^^
+
+- [adc] Fix 11db deprecation warning :esphomepr:`6749` by :ghuser:`jesserockz` (notable-change)
+
+All changes
+^^^^^^^^^^^
+
+- Add some components to the new testing framework (H) :esphomepr:`6179` by :ghuser:`kbx81`
+- Added Htu21d model option :esphomepr:`6511` by :ghuser:`MRemy2`
+- Add bk72xx base test file :esphomepr:`6522` by :ghuser:`jesserockz`
+- Add "log" alias for "logs" command :esphomepr:`6519` by :ghuser:`pzich`
+- Add DNS sensor and simplify format :esphomepr:`6450` by :ghuser:`HeMan` (breaking-change)
+- Add all missing ``remote_receiver`` ``on_...`` tests :esphomepr:`6524` by :ghuser:`kbx81`
+- Add actions to http_request tests :esphomepr:`6529` by :ghuser:`kbx81`
+- Update homeassistant component tests with actions :esphomepr:`6528` by :ghuser:`kbx81`
+- Define ``USE_PSRAM`` :esphomepr:`6526` by :ghuser:`edwardtfn`
+- Bump black from 24.2.0 to 24.4.0 :esphomepr:`6539` by :ghuser:`dependabot[bot]`
+- Bump peter-evans/create-pull-request from 6.0.2 to 6.0.3 :esphomepr:`6525` by :ghuser:`dependabot[bot]`
+- Bump python version in sync-device-classes workflow to 3.12 for HA :esphomepr:`6541` by :ghuser:`jesserockz`
+- Bump pylint from 3.0.3 to 3.1.0 :esphomepr:`6287` by :ghuser:`dependabot[bot]`
+- Bump aioesphomeapi from 23.2.0 to 24.0.0 :esphomepr:`6544` by :ghuser:`dependabot[bot]`
+- Bump pyupgrade from 3.15.1 to 3.15.2 :esphomepr:`6543` by :ghuser:`dependabot[bot]`
+- Add enum option to typed_schema :esphomepr:`6546` by :ghuser:`jesserockz`
+- Move esphome-fork startup script to main repo. :esphomepr:`6523` by :ghuser:`jesserockz`
+- Call workflow for addon with dev version :esphomepr:`6549` by :ghuser:`jesserockz`
+- Use trusted publishing token for pypi :esphomepr:`6545` by :ghuser:`jesserockz`
+- Fix uart to work with new enum definition in esp-idf-v5.2.1 :esphomepr:`6487` by :ghuser:`luar123`
+- Housecleaning: Use walrus operator in datetime :esphomepr:`6552` by :ghuser:`jesserockz`
+- Housecleaning: Use walrus operator in text :esphomepr:`6560` by :ghuser:`jesserockz`
+- Housecleaning: Use walrus operator in light :esphomepr:`6556` by :ghuser:`jesserockz`
+- Housecleaning: Use walrus operator in select :esphomepr:`6557` by :ghuser:`jesserockz`
+- Housecleaning: Use walrus operator in number :esphomepr:`6561` by :ghuser:`jesserockz`
+- Housecleaning: Use walrus operator in cover :esphomepr:`6562` by :ghuser:`jesserockz`
+- Housecleaning: Use walrus operator in climate :esphomepr:`6551` by :ghuser:`jesserockz`
+- Housecleaning: Use walrus operator in fan :esphomepr:`6555` by :ghuser:`jesserockz`
+- Housecleaning: Use walrus operator in text_sensor :esphomepr:`6559` by :ghuser:`jesserockz`
+- Bump zeroconf to 0.132.2 :esphomepr:`6548` by :ghuser:`bdraco`
+- Housecleaning: Use walrus operator in switch :esphomepr:`6558` by :ghuser:`jesserockz`
+- Housecleaning: Use walrus operator in lock :esphomepr:`6554` by :ghuser:`jesserockz`
+- Housecleaning: Use walrus operator in sensor :esphomepr:`6553` by :ghuser:`jesserockz`
+- Bump pytest-mock from 3.12.0 to 3.14.0 :esphomepr:`6572` by :ghuser:`dependabot[bot]`
+- Bump peter-evans/create-pull-request from 6.0.3 to 6.0.4 :esphomepr:`6569` by :ghuser:`dependabot[bot]`
+- Nextion - Review set_protocol_reparse_mode() :esphomepr:`6567` by :ghuser:`edwardtfn`
+- Allow component final_validate :esphomepr:`6475` by :ghuser:`kbx81`
+- SM2135 - Use standard channel ordering. :esphomepr:`6573` by :ghuser:`Cossid` (breaking-change)
+- Nextion - Do not refresh sensors while updating :esphomepr:`6566` by :ghuser:`edwardtfn`
+- Nextion - Review types :esphomepr:`6565` by :ghuser:`edwardtfn`
+- On failure, dump the output of preceding jobs in CI status :esphomepr:`6564` by :ghuser:`clydebarrow`
+- Nextion ``send_command`` method :esphomepr:`6540` by :ghuser:`edwardtfn`
+- Fix some printf formats for size_t. :esphomepr:`6542` by :ghuser:`clydebarrow`
+- remove delay from tmp102 :esphomepr:`6577` by :ghuser:`ssieb`
+- Create ``component_dir`` substitution for local files to be included in… :esphomepr:`6575` by :ghuser:`jesserockz`
+- Define ``USE_ESP32_BLE`` :esphomepr:`6585` by :ghuser:`edwardtfn`
+- Bump aioesphomeapi from 24.0.0 to 24.3.0 :esphomepr:`6602` by :ghuser:`dependabot[bot]`
+- Add yamllint and clang-format to pre-commit hooks :esphomepr:`6578` by :ghuser:`clydebarrow`
+- Use clang-format version from requirements_dev file :esphomepr:`6606` by :ghuser:`jesserockz`
+- Add some components to the new testing framework (P) :esphomepr:`6213` by :ghuser:`kbx81`
+- Add some components to the new testing framework (M part 1) :esphomepr:`6207` by :ghuser:`kbx81`
+- Add some components to the new testing framework (M part 2) :esphomepr:`6208` by :ghuser:`kbx81`
+- Add some components to the new testing framework (O) :esphomepr:`6211` by :ghuser:`kbx81`
+- [mopeka_std_check] Fix test file indentation :esphomepr:`6610` by :ghuser:`jesserockz`
+- Add valve component :esphomepr:`6447` by :ghuser:`kbx81` (new-integration)
+- Add some components to the new testing framework (R) :esphomepr:`6219` by :ghuser:`kbx81`
+- [sn74hc595] Enforce type field to distinguish gpio vs spi mode :esphomepr:`6609` by :ghuser:`jesserockz` (breaking-change)
+- [tests] Run yaml tests in groups if over 100 to run :esphomepr:`6612` by :ghuser:`jesserockz`
+- Add some components to the new testing framework (I) :esphomepr:`6185` by :ghuser:`kbx81`
+- Add some components to the new testing framework (T) :esphomepr:`6229` by :ghuser:`kbx81`
+- Add some components to the new testing framework (S part 1) :esphomepr:`6224` by :ghuser:`kbx81`
+- Add some components to the new testing framework (S part 2) :esphomepr:`6227` by :ghuser:`kbx81`
+- ``graphical_display_menu`` requires a Display, not DisplayBuffer :esphomepr:`6614` by :ghuser:`clydebarrow`
+- Add null GPIO pin  :esphomepr:`6611` by :ghuser:`clydebarrow`
+- Allow UART to be AUTO LOADed :esphomepr:`6617` by :ghuser:`jesserockz`
+- Add the WeiKai SPI/I2C UART/IO Expander components to esphome  :esphomepr:`5218` by :ghuser:`DrCoolzic` (new-integration)
+- Sort mqtt_const alphabetically :esphomepr:`6619` by :ghuser:`jesserockz`
+- Limit Rx wait loop time to 3 seconds. :esphomepr:`6594` by :ghuser:`descipher`
+- Event entity support :esphomepr:`6451` by :ghuser:`nohat` (new-integration)
+- Only check c/c++ files with clang-format :esphomepr:`6620` by :ghuser:`jesserockz`
+- Added base64 helper :esphomepr:`4866` by :ghuser:`freekode`
+- Add Roomba IR protocol :esphomepr:`4595` by :ghuser:`rforro`
+- Fix issue when setting cw/ww brightness via temperature :esphomepr:`5976` by :ghuser:`patagonaa`
+- Add get/set color temperature functions in Kelvin :esphomepr:`5006` by :ghuser:`danielkent-net`
+- Move CONF_PLATFORM_VERSION to global const.py :esphomepr:`6629` by :ghuser:`tomaszduda23`
+- Ble client fixes for proxy :esphomepr:`6596` by :ghuser:`elupus`
+- Fix for #6614- use background_color, improve anti-aliasing :esphomepr:`6618` by :ghuser:`clydebarrow`
+- Fix graph hangs when y <= 0 :esphomepr:`6593` by :ghuser:`chiahsing`
+- Feature add last_operation to time based cover :esphomepr:`6084` by :ghuser:`xprofiler`
+- Add ``event``, ``text_sensor`` and ``valve`` device classes to sync script :esphomepr:`6624` by :ghuser:`kbx81`
+- Add datetime entities :esphomepr:`6513` by :ghuser:`jesserockz` (breaking-change)
+- Multiple Daly-BMS support :esphomepr:`6615` by :ghuser:`latonita`
+- Remove text_sensor from sync-device-class job :esphomepr:`6637` by :ghuser:`kbx81`
+- Synchronise Device Classes from Home Assistant :esphomepr:`6638` by :ghuser:`esphomebot`
+- Display: add diagnostic test_card option :esphomepr:`6608` by :ghuser:`nielsnl68`
+- waveshare_epaper: Add 2.90in-dke :esphomepr:`6492` by :ghuser:`polyfloyd`
+- Extract core comments from #6241 :esphomepr:`6643` by :ghuser:`javawizard`
+- [hm3301] Updated the AQI based on the airnow document :esphomepr:`6004` by :ghuser:`optimusprimespace`
+- Fix command line substitutions without any yaml substitutions :esphomepr:`6644` by :ghuser:`jesserockz`
+- Allow platform dependencies :esphomepr:`6623` by :ghuser:`kbx81`
+- [light] Add transition_length to strobe effect. :esphomepr:`6595` by :ghuser:`lhartmann`
+- Fixed the issue that graph draws out of the boundary. :esphomepr:`6651` by :ghuser:`chiahsing`
+- Fix upload command. MQTT user and password is missing from configuration. #5093 :esphomepr:`5766` by :ghuser:`dylan09`
+- patch esphome cli to skip mqtt based device discovery if --device option is specified :esphomepr:`6371` by :ghuser:`quigleymd`
+- Fix for #4866 - inconsistent arguments :esphomepr:`6639` by :ghuser:`clydebarrow`
+- [template/text] Fix lambda config :esphomepr:`6655` by :ghuser:`asergunov`
+- web_server: Add support for v3 local server_index :esphomepr:`6563` by :ghuser:`pzich`
+- Update webserver local assets to 20240429-211523 :esphomepr:`6657` by :ghuser:`esphomebot`
+- [nextion] Exit reparse before update TFT :esphomepr:`6589` by :ghuser:`edwardtfn`
+- [nextion] Set alternative TFT update baud rate :esphomepr:`6587` by :ghuser:`edwardtfn`
+- [TM1637] Let turn off the display :esphomepr:`6656` by :ghuser:`asergunov`
+- [nextion] Use persistent http connection for TFT upload (Arduino) :esphomepr:`6582` by :ghuser:`edwardtfn`
+- Extend MQTT tests :esphomepr:`6648` by :ghuser:`kbx81`
+- Extend and consolidate ``script`` tests :esphomepr:`6663` by :ghuser:`kbx81`
+- [nextion] Use persistent http connection for TFT upload (ESP-IDF) :esphomepr:`6576` by :ghuser:`edwardtfn`
+- Add a function to return the loop_interval :esphomepr:`6666` by :ghuser:`tronikos`
+- Remote receiver improvements :esphomepr:`4642` by :ghuser:`Mat931`
+- Make fast update intervals in qmc5883l work :esphomepr:`6647` by :ghuser:`tronikos`
+- SPI and I2C for BMP390 and BMP380 :esphomepr:`6652` by :ghuser:`latonita` (new-integration) (breaking-change)
+- Set ``CONF_`` CI counter to fail on 3 or more definitions :esphomepr:`6668` by :ghuser:`jesserockz`
+- [core] Rename ALWAYS_INLINE to ESPHOME_ALWAYS_INLINE :esphomepr:`6636` by :ghuser:`tomaszduda23`
+- print task name if logger is called from other than main thread :esphomepr:`6630` by :ghuser:`tomaszduda23`
+- Fix recent definitions into `defines.h` :esphomepr:`6667` by :ghuser:`edwardtfn`
+- Add fast update to HMC5883L :esphomepr:`6669` by :ghuser:`mkmer`
+- Minor tidy up of BME280 code :esphomepr:`6672` by :ghuser:`latonita`
+- External components: optional configurable path for git source :esphomepr:`6677` by :ghuser:`twasilczyk`
+- Use clang-apply-replacements when clang-apply-replacements-14 does not exist :esphomepr:`6684` by :ghuser:`Links2004`
+- fix conflict with EMPTY macro in zephyr :esphomepr:`6679` by :ghuser:`tomaszduda23`
+- Bump actions/checkout from 4.1.1 to 4.1.5 :esphomepr:`6685` by :ghuser:`dependabot[bot]`
+- Fix Datetime-Datetime compiler error :esphomepr:`6686` by :ghuser:`RFDarter`
+- Bump esphome/ESPAsyncWebServer-esphome to 3.2.0 :esphomepr:`6687` by :ghuser:`jesserockz`
+- fix date_time validation :esphomepr:`6688` by :ghuser:`RFDarter`
+- proceed if AP mode is set up :esphomepr:`6631` by :ghuser:`ssieb`
+- Migrate some constants to core code :esphomepr:`6692` by :ghuser:`clydebarrow`
+- Consolidate test files where all tests are identical :esphomepr:`6690` by :ghuser:`kbx81`
+- Make ``pulse_meter`` PULSE filter report the pulse as soon as it can :esphomepr:`6014` by :ghuser:`TrentHouliston`
+- Update webserver local assets to 20240507-231331 :esphomepr:`6696` by :ghuser:`esphomebot`
+- [github] Upgrade to actions/[upload,download]-artifact v4 :esphomepr:`6698` by :ghuser:`jesserockz`
+- [nextion] Replace flags to ``USE_ARDUINO`` :esphomepr:`6700` by :ghuser:`edwardtfn`
+- [remote_receiver, remote_transmitter] Improve error messages on the ESP32 :esphomepr:`6701` by :ghuser:`Mat931`
+- [ethernet] Use constexpr instead of inline define for KSZ80XX_PC2R_REG_ADDR :esphomepr:`6705` by :ghuser:`jesserockz`
+- Add PHY register writes to enable external clock on Ethernet with RTL8201 :esphomepr:`6704` by :ghuser:`heythisisnate`
+- Bump recommended ESP-IDF to 4.4.7 :esphomepr:`6703` by :ghuser:`bdraco`
+- [core] Ensure that a generated ID name is distinct from its type. :esphomepr:`6706` by :ghuser:`clydebarrow`
+- [color] Fix crash when hex color parses as int, improve error reporting. :esphomepr:`6707` by :ghuser:`clydebarrow`
+- [github] Fix digest artifact name :esphomepr:`6710` by :ghuser:`jesserockz`
+- fix(ltr390): stuck ALS values when configured for ALS+UV readings :esphomepr:`6723` by :ghuser:`CodeInPolish`
+- Set FEATURE_API_AUDIO flag also if the speaker component is not used :esphomepr:`6712` by :ghuser:`gnumpi`
+- Bump platformio from 6.1.13 to 6.1.15 :esphomepr:`6634` by :ghuser:`dependabot[bot]`
+- Fix ESPHOME_PROJECT_VERSION_30 :esphomepr:`6731` by :ghuser:`jesserockz`
+- Voice-Assistant: Start-order change for VAD disabled: start va-pipeline when microphon… :esphomepr:`6391` by :ghuser:`gnumpi`
+- Add ANNOUNCING state to media_player. :esphomepr:`6691` by :ghuser:`gnumpi`
+- [adc] Fix 11db deprecation warning :esphomepr:`6749` by :ghuser:`jesserockz` (notable-change)
+
+Past Changelogs
+---------------
+
+- :doc:`2024.4.0`
+- :doc:`2024.3.0`
+- :doc:`2024.2.0`
+- :doc:`2023.12.0`
+- :doc:`2023.11.0`
+- :doc:`2023.10.0`
+- :doc:`2023.9.0`
+- :doc:`2023.8.0`
+- :doc:`2023.7.0`
+- :doc:`2023.6.0`
+- :doc:`2023.5.0`
+- :doc:`2023.4.0`
+- :doc:`2023.3.0`
+- :doc:`2023.2.0`
+- :doc:`2022.12.0`
+- :doc:`2022.11.0`
+- :doc:`2022.10.0`
+- :doc:`2022.9.0`
+- :doc:`2022.8.0`
+- :doc:`2022.6.0`
+- :doc:`2022.5.0`
+- :doc:`2022.4.0`
+- :doc:`2022.3.0`
+- :doc:`2022.2.0`
+- :doc:`2022.1.0`
+- :doc:`2021.12.0`
+- :doc:`2021.11.0`
+- :doc:`2021.10.0`
+- :doc:`2021.9.0`
+- :doc:`2021.8.0`
+- :doc:`v1.20.0`
+- :doc:`v1.19.0`
+- :doc:`v1.18.0`
+- :doc:`v1.17.0`
+- :doc:`v1.16.0`
+- :doc:`v1.15.0`
+- :doc:`v1.14.0`
+- :doc:`v1.13.0`
+- :doc:`v1.12.0`
+- :doc:`v1.11.0`
+- :doc:`v1.10.0`
+- :doc:`v1.9.0`
+- :doc:`v1.8.0`
+- :doc:`v1.7.0`

changelog/index.rst

@@ -2,7 +2,7 @@ Changelog
 =========
 
 .. redirect::
-    :url: /changelog/2024.3.0.html
+    :url: /changelog/2024.5.0.html
 
 .. toctree::
     :glob:

changelog/v1.9.0.rst

@@ -30,7 +30,7 @@ awesome things with DIY hardware!
 
 The features I'm particularly excited about are:
 
-* :ref:`esphomeflasher <esphome-flasher>` - Experiencing problems flashing esphomelib firmwares using esphomeyaml?
+* ``esphomeflasher`` - Experiencing problems flashing esphomelib firmwares using esphomeyaml?
   No problem, esphomeflasher is a tool designed to make that super easy. Just let esphomeyaml generate the binary and flash
   from your PC.
 * :doc:`Over-the-Air Updates </components/ota>` have been completely re-written to make them a lot more
@@ -76,7 +76,7 @@ New Features
 
 - esphomelib now has a new tool: `esphomeflasher <https://github.com/esphome/esphome-flasher>`__ to simplify
   flashing on Windows/MacOS machines **without having to install esphomeyaml**. So if esphomeyaml for some reason
-  can't find your USB port, you now can use the esphomeflasher app. See :ref:`esphome-flasher`.
+  can't find your USB port, you now can use the esphomeflasher app. See ``esphomeflasher``.
 
 - ESP8266s now save the states of lights/switches/... internally and restores them on boot.
   Additionally, esphomelib can now operate in fully offline mode if your WiFi network goes down

components/alarm_control_panel/template.rst

@@ -169,7 +169,7 @@ Example:
         name: Zone 1
         device_class: door
         pin:
-          number: D1
+          number: GPIOXX
           mode: INPUT_PULLUP
           inverted: True
       - platform: gpio
@@ -177,7 +177,7 @@ Example:
         name: Zone 2
         device_class: door
         pin:
-          number: D2
+          number: GPIOXX
           mode: INPUT_PULLUP
           inverted: True
       - platform: gpio
@@ -185,7 +185,7 @@ Example:
         name: Zone 3
         device_class: motion
         pin:
-          number: D3
+          number: GPIOXX
           mode: INPUT_PULLUP
           inverted: True
       - platform: gpio
@@ -193,7 +193,7 @@ Example:
         name: Zone 4
         device_class: door
         pin:
-          number: D4
+          number: GPIOXX
           mode: INPUT_PULLUP
           inverted: True
       - platform: homeassistant
@@ -206,7 +206,7 @@ Example:
         id: siren
         name: Siren
         icon: mdi:alarm-bell
-        pin: D7
+        pin: GPIOXX
 
 
 See Also

components/api.rst

@@ -75,20 +75,35 @@ Configuration variables:
 
 .. _api-actions:
 
-.. note::
-
-    Before a newly added ESPHome device can interact with the Home Assistant API it needs to be allowed to communicate
-    with it. This setting can be found in the ESPHome integration (NOT in the Add-On) by clicking "CONFIGURE" for
-    that device and enabling the "Allow device to make service calls" option.
-
 Actions
 -------
 
+Before using any of the actions below, you'll need to tell Home Assistant to allow your device to
+make service calls.
+
+Open the ESPHome integration page on your Home Assistant instance:
+
+.. raw:: html
+
+    <a href="https://my.home-assistant.io/redirect/integration/?domain=esphome" target="_blank" rel="noreferrer noopener"><img src="https://my.home-assistant.io/badges/integration.svg" alt="Open your Home Assistant instance and show an integration." /></a>
+
+Then:
+
+#. Fnd your device in the device list
+#. Click the "configure" button next to it
+#. Check the "Allow the device to make Home Assistant service calls" box
+#. Then click "submit".
+
 .. _api-homeassistant_event_action:
 
 ``homeassistant.event`` Action
 ******************************
 
+.. note::
+
+    Be sure to :ref:`follow the instructions above <api-actions>` to tell Home Assistant to allow
+    your device to make service calls.
+
 When using the native API with Home Assistant, you can create events in the Home Assistant event bus
 straight from ESPHome :ref:`Automations <automation>`.
 
@@ -117,6 +132,11 @@ Configuration variables:
 ``homeassistant.service`` Action
 ********************************
 
+.. note::
+
+    Be sure to :ref:`follow the instructions above <api-actions>` to tell Home Assistant to allow
+    your device to make service calls.
+
 When using the native API with Home Assistant, you can create Home Assistant service
 calls straight from ESPHome :ref:`Automations <automation>`.
 
@@ -189,6 +209,11 @@ Then, in ESPHome:
 ``homeassistant.tag_scanned`` Action
 ************************************
 
+.. note::
+
+    Be sure to :ref:`follow the instructions above <api-actions>` to tell Home Assistant to allow
+    your device to make service calls.
+
 When using the native API with Home Assistant, you can push tag_scanned to Home Assistant
 straight from ESPHome :ref:`Automations <automation>`.
 

components/at581x.rst

@@ -0,0 +1,183 @@
+AirTouch AT581x Radar
+=====================
+
+.. seo::
+    :description: Instructions for setting up AirTouch AT581x Radar
+    :image: at581x.png
+    :keywords: radar
+
+The `AirTouch AT581x radar <https://en.airtouching.com/product/32.html>`__
+(aka ``AT581x``) is a familly of 5.8GHz radar which can be used for human presence detection. It can detect tiny movements
+and compared to a PIR sensor **it can detect presence continuously**. This can be useful, for example, to turn
+the lights on when you enter a room, keep them on as long as you are there (without waving your hands at the
+sensor) and turn them off almost immediately after you leave the room.
+
+They are ultra-low power (as low as 40µA of current consumption) and are extremely simple to use, yet can be setup by I2C.
+It's installed in many low cost appliance, like the ESP32S3-BOX-3, and can be found by many different manufacturer or reference,
+like the MoreSense MS58-3909S68U4.
+
+It is possible to use this sensor with only a single GPIO pin; however, if you wish to change its settings,
+a :doc:`/components/i2c` component (and its requisite GPIO pins) is required in your device's configuration.
+
+.. figure:: ../images/at581x.png
+    :align: center
+    :width: 75%
+
+    AirTouch AT581x Radar / presence detection sensor
+
+.. code-block:: yaml
+
+    # Example configuration entry
+    at581x:
+      id: "Radar"
+      i2c_id: bus_a
+
+.. _at581x-component:
+
+Component/Hub
+-------------
+
+You need to have the hub component (``at581x:`` entry) defined to be able to change the sensor's
+settings, get it listed as an motion entity or being able to turn on/off the radio frequency emmission.
+A :doc:`/components/binary_sensor/gpio` alone could be sufficient if you only want
+to determine presence/occupancy. When you define ``at581x:`` you'll need to have a ``i2c:`` entry in
+your configuration with both the SDA and SCL pins defined.
+
+Multiple instances of this component may be defined if multiple :doc:`/components/i2c` components are available:
+
+.. code-block:: yaml
+
+    at581x:
+      - id: mmWave_1
+        i2c_id: bus_a
+        address: 0x28
+      - id: mmWave_2
+        i2c_id: bus_a
+        address: 0x29
+      ...
+
+Configuration variables:
+************************
+
+- **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation. Necessary if you want
+  to define multiple instances of this component.
+- **i2c_id** (*Optional*, :ref:`config-id`): Manually specify the ID of the :doc:`/components/i2c` if you want
+  to use multiple I2C buses.
+
+.. _at581x-binary_sensor:
+
+Binary Sensor
+-------------
+
+The state of the radar detection is available via its GPIO pin. It's required to use a GPIO binary sensor to monitor the motion status
+
+.. code-block:: yaml
+
+    binary_sensor:
+      - platform: gpio
+        name: "Human in front"
+        pin: GPIOXX
+
+Configuration variables:
+************************
+
+- Refer to other options from :ref:`Binary Sensor <config-binary_sensor>` and :doc:`GPIO Binary Sensor </components/binary_sensor/gpio>`.
+
+.. _at581x-switch:
+
+Switch
+------
+
+:ref:`Switch components <config-switch>` are used to enable/disable radio frequency hardware.
+
+.. code-block:: yaml
+
+    switch:
+      - platform: at581x
+        at581x_id: Radar
+        name: "Enable Radar"
+
+Configuration variables:
+************************
+
+- **at581x_id** (*Optional*, :ref:`config-id`): The ID of the AT581x component defined above.
+  Required when multiple instances of the ``at581x`` component are defined.
+- All other options from :ref:`Switch <config-switch>`.
+
+.. _at581x-actions:
+
+Actions
+-------
+
+.. _at581x-action_settings:
+
+``at581x.settings`` Action
+**************************
+
+.. warning::
+
+    The hardware frontend reset option is only required to reset the frontend in case it is struck, before sending the
+    new configuration. However, a frontend reset is always performed after changing the settings.
+
+The radar has several settings which can be changed. These settings are not saved in non-volatile memory
+and need to be set on each boot.
+
+The settings action allows changing of any number of the radar's internal parameters/settings. With this
+action, any unspecified parameters will remain unchanged.
+
+.. code-block:: yaml
+
+    on_...:
+      - at581x.settings:
+          id: "Waveradar"
+          hw_frontend_reset: false
+          frequency: 5800MHz
+          sensing_distance: 200 # 0-1023
+          poweron_selfcheck_time: 2000ms
+          protect_time: 1s
+          trigger_base: 500ms
+          trigger_keep: 10s
+          stage_gain: 3 # 0-12 the higher the value the smaller the gain
+          power_consumption: 70µA
+
+
+Configuration variables:
+````````````````````````
+
+- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the sensor on which settings should be
+  changed. If only one radar is defined, this is optional.
+- **hw_frontend_reset** (*Optional*, boolean): If set to true, a reset of the analog frontend will be performed before
+  changing other options. Ignored if not set or set to ``false``. Upon applying the settings a frontend reset
+  will be performed anyway, this is only useful if the sensor is not answering or locked up.
+- **frequency** (*Optional*, int): Any of the possible frequencies (5696, 5715, 5730, 5748, 5765, 5784, 5800, 5819, 5836, 5851, 5869, 5888) in MHz.
+- **sensing_distance** (*Optional*, int): A unitless number, in range 0-1023, specifying the maximum distance to detect motion
+- **poweron_selfcheck_time** (*Optional*, int): The delay to perform self check and calibration on power on. Recommanded not to change this
+- **protect_time** (*Optional*, int): The delay after an end-of-trigger event where the detection will not trigger anymore. Max 65535ms
+- **trigger_base** (*Optional*, int): The delay while a detection must be active to change the state of the sensor. Max 65535ms
+- **trigger_keep** (*Optional*, int): The delay that the output will stay high after a detection event. This is usually what you want to change.
+- **stage_gain** (*Optional*, int): The analog gain to use for threshold test. Any value in range 0-12, with 12 being the lowest gain and 0 the highest
+- **power_consumption** (*Optional*, int): Any of the possible power profile (48, 56, 63, 70, 77, 91, 105, 115, 40, 44, 47, 51, 54, 61, 68, 78) in µA
+
+
+``at581x.reset`` Action
+***********************
+
+Restart the sensor.
+
+.. code-block:: yaml
+
+    on_...:
+      at581x.reset:
+
+Configuration variables:
+````````````````````````
+
+- **id** (*Optional*, :ref:`config-id`): Manually specify the ID of the AT581x component. Useful when multiple instances of this component are defined.
+
+See Also
+--------
+- :ref:`I2C bus <i2c>`
+- :ref:`Binary Sensor <config-binary_sensor>`
+- :doc:`GPIO Binary Sensor </components/binary_sensor/gpio>`
+- :ref:`config-id`
+- :ghedit:`Edit`

components/binary_sensor/cap1188.rst

@@ -30,7 +30,7 @@ required to be set up in your configuration for this sensor to work.
     cap1188:
       id: cap1188_component
       address: 0x29
-      reset_pin: 14
+      reset_pin: GPIOXX
       touch_threshold: 0x40
       allow_multiple_touches: true
 

components/binary_sensor/custom.rst

@@ -1,22 +1,28 @@
 Custom Binary Sensor
 ====================
 
+.. seo::
+    :description: Instructions for setting up Custom C++ binary sensors with ESPHome.
+    :image: language-cpp.svg
+    :keywords: C++, Custom
+
 .. warning::
 
-    Custom components are deprecated, not recommended for new configurations
-    and will be removed from ESPHome in a future release.
-    Please look at creating a real ESPHome component and "importing" it into your
-    configuration with :doc:`/components/external_components`.
+    Custom components are deprecated, not recommended for new configurations and will be removed from ESPHome in a
+    future release. Please look at creating a real ESPHome component and "importing" it into your configuration with
+    :doc:`/components/external_components`.
 
-    You can find some basic documentation on creating your own components
-    at :ref:`contributing_to_esphome`.
+    You can find some basic documentation on creating your own components at :ref:`contributing_to_esphome`.
 
-This integration can be used to create custom binary sensors in ESPHome
-using the C++ (Arduino) API.
+.. warning::
 
-Please first read :doc:`/components/sensor/custom` guide,
-the same principles apply here and binary sensors are very similar
-to sensors internally.
+    While we try to keep the ESPHome YAML configuration options as stable as possible, the ESPHome API is less
+    stable. If something in the APIs needs to be changed in order for something else to work, we will do so.
+
+This component can be used to create custom binary sensors in ESPHome using the C++ (Arduino) API.
+
+Please first read :doc:`/components/sensor/custom` guide, the same principles apply here and binary
+sensors are very similar to sensors internally.
 
 The example below is an example of a custom binary sensor; this custom sensor is essentially the
 same as the gpio binary sensor.

components/binary_sensor/esp32_touch.rst

@@ -130,8 +130,8 @@ an ``OFF`` state.
 
     binary_sensor:
       - platform: esp32_touch
-        name: "ESP32 Touch Pad GPIO27"
-        pin: GPIO27
+        name: "ESP32 Touch Pad"
+        pin: GPIOXX
         threshold: 1000
 
 Configuration variables:
@@ -149,6 +149,35 @@ Configuration variables:
    wake-up from a touch event. Note that no filter(s) is/are active during deep sleep.
 -  All other options from :ref:`Binary Sensor <config-binary_sensor>`.
 
+
+Raw Values
+----------
+
+If access to the raw values is required, a template sensor can be created that polls for them:
+
+.. code-block:: yaml
+
+    # Example configuration entry for accessing raw values
+    esp32_touch:
+      id: esp32_touch_1
+
+    binary_sensor:
+      - platform: esp32_touch
+        id: esp32_touch_pad
+        pin: GPIOXX
+        threshold: 0
+
+    sensor:
+      - platform: template
+        name: "Raw touch value"
+        lambda: |-
+            return id(esp32_touch_pad).get_value();
+        update_interval: 3s
+
+One example of use is a wide area pressure sensor that integrates a number of smaller sensors in an area. Make two strips
+of aluminium foil that sandwich paper, and connect one wire to a touch pin and the other to ground. Set up several sensors
+under a flexible object like a plastic mat, add the raw values, and apply a threshold.
+
 .. _esp32-touch-pad-pins:
 
 Touch Pad Pins

components/binary_sensor/haier.rst

@@ -17,8 +17,8 @@ Additional sensors for Haier Climate device. **These sensors are supported only
     # Example configuration entry
     uart:
       baud_rate: 9600
-      tx_pin: 17
-      rx_pin: 16
+      tx_pin: GPIOXX
+      rx_pin: GPIOXX
       id: ac_port
 
     climate:

components/binary_sensor/homeassistant.rst

@@ -34,7 +34,6 @@ Configuration variables:
 - **entity_id** (**Required**, string): The entity ID to import from Home Assistant.
 - **attribute** (*Optional*, string): The name of the state attribute to import from the
   specified entity. The entity state is used when this option is omitted.
-  Requires Home Assistant 2021.6 or newer.
 - **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation.
 - All other options from :ref:`Binary Sensor <config-binary_sensor>`.
 

components/binary_sensor/hydreon_rgxx.rst

@@ -12,12 +12,6 @@ For this sensor to work, a :doc:`/components/sensor/hydreon_rgxx` must be set up
 .. code-block:: yaml
 
     # Example RG-9 entry
-
-    uart:
-      rx_pin: GPIO16
-      tx_pin: GPIO17
-      baud_rate: 9600
-
     sensor:
       - platform: hydreon_rgxx
         model: "RG_9"

components/binary_sensor/index.rst

@@ -66,12 +66,12 @@ Advanced options:
   a ``name`` will implicitly set this to true.
 - **disabled_by_default** (*Optional*, boolean): If true, then this entity should not be added to any client's frontend,
   (usually Home Assistant) without the user manually enabling it (via the Home Assistant UI).
-  Requires Home Assistant 2021.9 or newer. Defaults to ``false``.
+  Defaults to ``false``.
 - **publish_initial_state** (*Optional*, boolean): If true, then the sensor will publish its initial state at boot or when
   HA first connects, depending on the platform.  This means that any applicable triggers will be run. Defaults to ``false``.
 - **entity_category** (*Optional*, string): The category of the entity.
   See https://developers.home-assistant.io/docs/core/entity/#generic-properties
-  for a list of available options. Requires Home Assistant 2021.11 or newer.
+  for a list of available options.
   Set to ``""`` to remove the default entity category.
 - If MQTT enabled, all other options from :ref:`MQTT Component <config-mqtt-component>`.
 

components/binary_sensor/rc522.rst

@@ -42,7 +42,7 @@ you can then create individual binary sensors that track if an NFC/RFID tag is c
     spi:
 
     rc522_spi:
-      cs_pin: GPIO15
+      cs_pin: GPIOXX
 
     binary_sensor:
       - platform: rc522

components/bluetooth_proxy.rst

@@ -43,15 +43,11 @@ Configuration:
 
     bluetooth_proxy:
 
-- **active** (*Optional*, boolean): Enables proxying active connections. Defaults to ``false``. Requires Home Assistant 2022.10 or later.
+- **active** (*Optional*, boolean): Enables proxying active connections. Defaults to ``false``.
 - **cache_services** (*Optional*, boolean): Enables caching GATT services in NVS flash storage which significantly speeds up active connections. Defaults to ``true`` when using the ESP-IDF framework.
 
 The Bluetooth proxy depends on :doc:`esp32_ble_tracker` so make sure to add that to your configuration.
 
-.. note::
-
-    Bluetooth proxy requires Home Assistant 2022.9 or later. ESPHome 2022.12.0 and Home Assistant 2022.12.6 or later is recommended.
-
 Improving reception performance
 -------------------------------
 

components/button/output.rst

@@ -17,7 +17,7 @@ momentarily set a GPIO pin using a button.
     # Example configuration entry
     output:
       - platform: gpio
-        pin: 25
+        pin: GPIOXX
         id: output1
 
     button:

components/button/uart.rst

@@ -11,10 +11,6 @@ The ``uart`` button platform allows you to send a pre-defined sequence of bytes
 .. code-block:: yaml
 
     # Example configuration entry
-    uart:
-      baud_rate: 9600
-      tx_pin: D0
-
     button:
       - platform: uart
         name: "UART String Output"

components/canbus.rst

@@ -197,8 +197,8 @@ You only need to specify the RX and TX pins. Any GPIO will work.
     # Example configuration entry
     canbus:
       - platform: esp32_can
-        tx_pin: GPIO5
-        rx_pin: GPIO4
+        tx_pin: GPIOXX
+        rx_pin: GPIOXX
         can_id: 4
         bit_rate: 50kbps
         on_frame:
@@ -273,7 +273,7 @@ For wiring up the MSP2515 please refer to the section below.
     # Example configuration entry
     canbus:
       - platform: mcp2515
-        cs_pin: D5
+        cs_pin: GPIOXX
         can_id: 4
         bit_rate: 50kbps
         on_frame:
@@ -359,7 +359,7 @@ Standard IDs and Extended IDs can coexist on the same segment.
       - platform: mcp2515
         id: my_mcp2515
         spi_id: McpSpi
-        cs_pin: GPIO14
+        cs_pin: GPIOXX
         can_id: 0x1fff
         use_extended_id: true
         bit_rate: 125kbps
@@ -385,9 +385,9 @@ Button is connected on a can node which sends an A message on ID 0x100 with payl
 
     spi:
       id: McpSpi
-      clk_pin: GPIO16
-      mosi_pin: GPIO5
-      miso_pin: GPIO4
+      clk_pin: GPIOXX
+      mosi_pin: GPIOXX
+      miso_pin: GPIOXX
 
     binary_sensor:
       - platform: template
@@ -398,7 +398,7 @@ Button is connected on a can node which sends an A message on ID 0x100 with payl
       - platform: mcp2515
         id: my_mcp2515
         spi_id: McpSpi
-        cs_pin: GPIO14
+        cs_pin: GPIOXX
         can_id: 4
         bit_rate: 125kbps
         on_frame:
@@ -430,15 +430,15 @@ Buttons are connected on the CAN-Node and also the motor is connected via CAN.
 
     spi:
       id: McpSpi
-      clk_pin: GPIO16
-      mosi_pin: GPIO5
-      miso_pin: GPIO4
+      clk_pin: GPIOXX
+      mosi_pin: GPIOXX
+      miso_pin: GPIOXX
 
     canbus:
       - platform: mcp2515
         id: my_mcp2515
         spi_id: McpSpi
-        cs_pin: GPIO14
+        cs_pin: GPIOXX
         can_id: 4
         bit_rate: 125kbps
         on_frame:

components/climate/bang_bang.rst

@@ -10,8 +10,7 @@ The ``bang_bang`` climate platform allows you to regulate a value with a
 
 .. note::
 
-    A number of people have asked about the behavior of the bang-bang controller. In version 1.15, a
-    :doc:`thermostat <thermostat>` component was added which behaves more like a common thermostat; it is
+    The :doc:`thermostat <thermostat>` component behaves more like a common thermostat; it is
     essentially two bang-bang controllers in one. Please see the `Bang-bang vs. Thermostat`_ section below
     if you are not sure which is appropriate for your application.
 

components/climate/climate_ir.rst

@@ -27,6 +27,8 @@ submit a feature request (see FAQ).
 +---------------------------------------+---------------------+----------------------+
 | Daikin                                | ``daikin``          | yes                  |
 +---------------------------------------+---------------------+----------------------+
+| :ref:`Daikin ARC<daikin_arc>`         | ``daikin_arc``      | yes                  |
++---------------------------------------+---------------------+----------------------+
 | :ref:`Daikin BRC<daikin_brc>`         | ``daikin_brc``      | yes                  |
 +---------------------------------------+---------------------+----------------------+
 | :ref:`Delonghi<delonghi_ir>`          | ``delonghi``        | yes                  |
@@ -42,7 +44,7 @@ submit a feature request (see FAQ).
 +---------------------------------------+---------------------+----------------------+
 | :ref:`LG<climate_ir_lg>`              | ``climate_ir_lg``   | yes                  |
 +---------------------------------------+---------------------+----------------------+
-| Midea                                 | ``midea_ir``        | yes                  |
+| :ref:`Midea<midea_ir>`                | ``midea_ir``        | yes                  |
 +---------------------------------------+---------------------+----------------------+
 | :ref:`Mitsubishi<mitsubishi>`         | ``mitsubishi``      | yes                  |
 +---------------------------------------+---------------------+----------------------+
@@ -74,7 +76,7 @@ controller unit.
 
     # Example configuration entry
     remote_transmitter:
-      pin: GPIO32
+      pin: GPIOXX
       carrier_duty_percent: 50%
 
     climate:
@@ -154,7 +156,7 @@ IR receiver.
     remote_receiver:
       id: rcvr
       pin:
-        number: GPIO14
+        number: GPIOXX
         inverted: true
         mode:
           input: true
@@ -167,35 +169,6 @@ IR receiver.
         name: "Living Room AC"
         receiver_id: rcvr
 
-.. _midea_ir:
-
-``midea_ir`` Climate
--------------------------
-
-These air conditioners support two protocols: Midea and Coolix. Therefore, when using an IR receiver, it considers both protocols and publishes the received states.
-
-Additional configuration is available for this platform
-
-
-Configuration variables:
-
-- **use_fahrenheit** (*Optional*, boolean): Allows you to transfer the temperature to the air conditioner in degrees Fahrenheit. The air conditioner display also shows the temperature in Fahrenheit. Defaults to ``false``.
-
-.. code-block:: yaml
-
-    # Example configuration entry
-    climate:
-      - platform: midea_ir
-        name: "AC"
-        sensor: room_temperature
-        use_fahrenheit: true
-
-.. note::
-
-    - See :ref:`Transmit Midea<remote_transmitter-transmit_midea>` to send custom commands, including Follow Me mode.
-    - See :ref:`Toshiba<toshiba>` below if you are looking for compatibility with Midea model MAP14HS1TBL or similar.
-
-
 .. _climate_ir_lg:
 
 ``climate_ir_lg`` Climate
@@ -222,6 +195,21 @@ Configuration variables:
         header_high: 3265us # AC Units from LG in Brazil, for example use these timings
         header_low: 9856us
 
+.. _daikin_arc:
+
+``daikin_arc`` Climate
+-------------------------
+
+The Daikin ARC remotes are used by the japanese model of Daikin.
+
+.. code-block:: yaml
+
+    # Example configuration entry
+    climate:
+      - platform: daikin_arc
+        name: "AC"
+        sensor: room_temperature
+
 .. _daikin_brc:
 
 ``daikin_brc`` Climate
@@ -255,6 +243,34 @@ Known working with:
 
 - Delonghi PAC WE 120HP
 
+.. _midea_ir:
+
+``midea_ir`` Climate
+-------------------------
+
+These air conditioners support two protocols: Midea and Coolix. Therefore, when using an IR receiver, it considers both protocols and publishes the received states.
+
+Additional configuration is available for this platform
+
+
+Configuration variables:
+
+- **use_fahrenheit** (*Optional*, boolean): Allows you to transfer the temperature to the air conditioner in degrees Fahrenheit. The air conditioner display also shows the temperature in Fahrenheit. Defaults to ``false``.
+
+.. code-block:: yaml
+
+    # Example configuration entry
+    climate:
+      - platform: midea_ir
+        name: "AC"
+        sensor: room_temperature
+        use_fahrenheit: true
+
+.. note::
+
+    - See :ref:`Transmit Midea<remote_transmitter-transmit_midea>` to send custom commands, including Follow Me mode.
+    - See :ref:`Toshiba<toshiba>` below if you are looking for compatibility with Midea model MAP14HS1TBL or similar.
+
 .. _mitsubishi:
 
 ``mitsubishi`` Climate

components/climate/custom.rst

@@ -1,21 +1,27 @@
 Custom Climate
 ==============
 
+.. seo::
+    :description: Instructions for setting up Custom C++ climate components with ESPHome.
+    :image: language-cpp.svg
+    :keywords: C++, Custom
+
 .. warning::
 
-    Custom components are deprecated, not recommended for new configurations
-    and will be removed from ESPHome in a future release.
-    Please look at creating a real ESPHome component and "importing" it into your
-    configuration with :doc:`/components/external_components`.
+    Custom components are deprecated, not recommended for new configurations and will be removed from ESPHome in a
+    future release. Please look at creating a real ESPHome component and "importing" it into your configuration with
+    :doc:`/components/external_components`.
 
-    You can find some basic documentation on creating your own components
-    at :ref:`contributing_to_esphome`.
+    You can find some basic documentation on creating your own components at :ref:`contributing_to_esphome`.
 
-This integration can be used to create custom climate devices in ESPHome
-using the C++ (Arduino) API.
+.. warning::
 
-Please first read :doc:`/components/sensor/custom` guide,
-the same principles apply here.
+    While we try to keep the ESPHome YAML configuration options as stable as possible, the ESPHome API is less
+    stable. If something in the APIs needs to be changed in order for something else to work, we will do so.
+
+This component can be used to create custom climate devices in ESPHome using the C++ (Arduino) API.
+
+Please first read :doc:`/components/sensor/custom` guide, the same principles apply here.
 
 The example below is an example of a custom climate device - all climate devices must override
 two methods (:apiclass:`Climate <climate::Climate>`):

components/climate/haier.rst

@@ -58,13 +58,6 @@ This component requires a :ref:`uart` to be setup.
 .. code-block:: yaml
 
     # Example configuration entry
-
-    uart:
-      baud_rate: 9600
-      tx_pin: 17
-      rx_pin: 16
-      id: ac_port  
-    
     climate:
       - platform: haier
         id: haier_ac

components/climate/index.rst

@@ -80,10 +80,10 @@ Advanced options:
   a ``name`` will implicitly set this to true.
 - **disabled_by_default** (*Optional*, boolean): If true, then this entity should not be added to any client's frontend,
   (usually Home Assistant) without the user manually enabling it (via the Home Assistant UI).
-  Requires Home Assistant 2021.9 or newer. Defaults to ``false``.
+  Defaults to ``false``.
 - **entity_category** (*Optional*, string): The category of the entity.
   See https://developers.home-assistant.io/docs/core/entity/#generic-properties
-  for a list of available options. Requires Home Assistant 2021.11 or newer.
+  for a list of available options.
   Set to ``""`` to remove the default entity category.
 
 MQTT options:

components/climate/midea.rst

@@ -25,17 +25,6 @@ The ``midea`` component creates a Midea air conditioner climate device.
 .. code-block:: yaml
 
     # Example configuration entry
-
-    # Disable logging over UART (required)
-    logger:
-      baud_rate: 0
-
-    # UART settings for Midea dongle (required)
-    uart:
-      tx_pin: 1         # hardware dependant
-      rx_pin: 3         # hardware dependant
-      baud_rate: 9600
-
     # Main settings
     climate:
       - platform: midea

components/climate/tuya.rst

@@ -39,8 +39,10 @@ Based on this, you can create the climate device as follows:
         switch_datapoint: 1
         target_temperature_datapoint: 3
         current_temperature_datapoint: 4
-        eco_datapoint: 7
-        eco_temperature: 20 °C
+        preset:
+          eco:
+            datapoint: 8
+            temperature: 28
 
 Configuration variables:
 ------------------------
@@ -50,16 +52,40 @@ Configuration variables:
 - **supports_heat** (*Optional*, boolean): Specifies if the device has a heating mode. Defaults to ``true``.
 - **supports_cool** (*Optional*, boolean): Specifies if the device has a cooling mode. Defaults to ``false``.
 - **switch_datapoint** (**Required**, int): The datapoint id number of the climate switch (device on/off).
-- **active_state_datapoint** (*Optional*, int): The datapoint id number of the active state - :ref:`see below <active_state_detection>`.
-- **active_state_heating_value** (*Optional*, int): The active state datapoint value the device reports when heating. Defaults to ``1`` - :ref:`see below <active_state_detection>`.
-- **active_state_cooling_value** (*Optional*, int): The active state datapoint value the device reports when cooling - :ref:`see below <active_state_detection>`.
+- **active_state** (*Optional*): Configuration for the Active State Configuration.
+
+    - **datapoint** (**Required**, int): The datapoint id number of the active state - :ref:`see below <active_state_detection>`.
+    - **heating_value** (*Optional*, int): The active state datapoint value the device reports when heating. Defaults to ``1`` - :ref:`see below <active_state_detection>`.
+    - **cooling_value** (*Optional*, int): The active state datapoint value the device reports when cooling - :ref:`see below <active_state_detection>`.
+    - **drying_value** (*Optional*, int): The active state datapoint value the device reports when in drying mode.
+    - **fanonly_value** (*Optional*, int): The active state datapoint value the device reports when in Fan Only mode.
+- **preset** (*Optional*): Configuration for presets.
+
+    - **eco** (*Optional*): Configuration for Eco preset.
+
+        - **datapoint** (**Required**, int): The datapoint id number of the Eco action.
+        - **temperature** (*Optional*, int): Temperature setpoint for Eco preset.
+    - **sleep** (*Optional*): Configuration for Sleep preset
+
+        - **datapoint** (**Required**, int): The Datapoint id number of the Sleep Action
+- **swing_mode** (*Optional*): Configuration for the swing (oscillation) modes.
+
+    - **vertical_datapoint** (*Optional*, int): The datapoint id number of the vertical swing action.
+    - **horizontal_datapoint** (*Optional*, int): The datapoint id number of the horizontal swing action.
+- **fan_mode** (*Optional*): Configuration for fan modes/fan speeds.
+
+    - **datapoint** (**Required**, int): The datapoint id number of the Fan value state.
+    - **auto_value** (*Optional*, int): The datapoint value the device reports when the fan is on ``auto`` speed.
+    - **low_value** (*Optional*, int):  The datapoint value the device reports when the fan is on ``low`` speed.
+    - **medium_value** (*Optional*, int):  The datapoint value the device reports when the fan is on ``medium`` speed.
+    - **middle_value** (*Optional*, int):  The datapoint value the device reports when the fan is on ``middle`` speed. (May set to device's ``high`` value if you have a ``Turbo`` option).
+    - **high_value** (*Optional*, int):  The datapoint value the device reports when the fan is on ``high`` speed. (Sometimes called ``Turbo``).
 - **heating_state_pin** (*Optional*, :ref:`config-pin`): The input pin indicating that the device is heating - :ref:`see below <active_state_detection>`. Only used if **active_state_datapoint** is not configured.
 - **cooling_state_pin** (*Optional*, :ref:`config-pin`): The input pin indicating that the device is cooling - :ref:`see below <active_state_detection>`. Only used if **active_state_datapoint** is not configured.
 - **target_temperature_datapoint** (**Required**, int): The datapoint id number of the target temperature.
 - **current_temperature_datapoint** (**Required**, int): The datapoint id number of the current temperature.
 - **temperature_multiplier** (*Optional*, float): A multiplier to modify the incoming and outgoing temperature values - :ref:`see below <temperature-multiplier>`.
-- **eco_datapoint** (*Optional*, int): The datapoint id number of the eco mode state.
-- **eco_temperature** (*Optional*, float): The target temperature the controller uses while the eco mode is active.
+
 - **reports_fahrenheit** (*Optional*, boolean): Set to ``true`` if the device reports temperatures in Fahrenheit. ESPHome expects all climate temperatures to be in Celcius, otherwise unexpected conversions will take place when it is published to Home Assistant. Defaults to ``false``.
 
 If the device has different multipliers for current and target temperatures, **temperature_multiplier** can be replaced with both of:

components/copy.rst

@@ -1,11 +1,11 @@
-Copy Integration
-================
+Copy Component
+==============
 
 .. seo::
-    :description: Instructions for setting up the copy integration in ESPHome
+    :description: Instructions for setting up the copy component in ESPHome
     :image: content-copy.svg
 
-The ``copy`` integration can be used to copy an existing component (like a sensor, switch, etc.)
+The ``copy`` component can be used to copy an existing component (like a sensor, switch, etc.)
 and create a duplicate mirroring the source's state and forwarding actions such as turning on to the source.
 
 For each of the supported platforms, the configuration consists of the required configuration

components/cover/custom.rst

@@ -1,24 +1,29 @@
 Custom Cover
 ============
 
+.. seo::
+    :description: Instructions for setting up Custom C++ covers with ESPHome.
+    :image: language-cpp.svg
+    :keywords: C++, Custom
+
 .. warning::
 
-    Custom components are deprecated, not recommended for new configurations
-    and will be removed from ESPHome in a future release.
-    Please look at creating a real ESPHome component and "importing" it into your
-    configuration with :doc:`/components/external_components`.
+    Custom components are deprecated, not recommended for new configurations and will be removed from ESPHome in a
+    future release. Please look at creating a real ESPHome component and "importing" it into your configuration with
+    :doc:`/components/external_components`.
 
-    You can find some basic documentation on creating your own components
-    at :ref:`contributing_to_esphome`.
+    You can find some basic documentation on creating your own components at :ref:`contributing_to_esphome`.
 
-This integration can be used to create custom covers in ESPHome
-using the C++ (Arduino) API.
+.. warning::
 
-Please first read :doc:`/components/sensor/custom` guide,
-the same principles apply here.
+    While we try to keep the ESPHome YAML configuration options as stable as possible, the ESPHome API is less
+    stable. If something in the APIs needs to be changed in order for something else to work, we will do so.
 
-The example below is an example of a custom cover - all covers must override
-two methods:
+This component can be used to create custom covers in ESPHome using the C++ (Arduino) API.
+
+Please first read :doc:`/components/sensor/custom` guide, the same principles apply here.
+
+The example below is an example of a custom cover - all covers must override two methods:
 
 - ``get_traits``: This should return a :apiclass:`CoverTraits <cover::CoverTraits>` object
   representing the capabilities of the cover.

components/cover/he60r.rst

@@ -26,8 +26,8 @@ below for a sample hardware interface.
         baud_rate: 1200
         parity: even
         stop_bits: 1
-        tx_pin: REPLACEME
-        rx_pin: REPLACEME
+        tx_pin: GPIOXX
+        rx_pin: GPIOXX
 
     cover:
       platform: he60r
@@ -72,9 +72,9 @@ Note that this circuit inverts the TX line. A configuration for this would look
         parity: even
         stop_bits: 1
         tx_pin:
-          number: REPLACEME
+          number: GPIOXX
           inverted: true
-        rx_pin: REPLACEME
+        rx_pin: GPIOXX
 
     cover:
       platform: he60r
@@ -84,7 +84,7 @@ Note that this circuit inverts the TX line. A configuration for this would look
     binary_sensor:
       - platform: gpio
         pin:
-          number: REPLACEME
+          number: GPIOXX
           inverted: true
           mode:
             input: true

components/cover/index.rst

@@ -46,10 +46,10 @@ Advanced options:
   a ``name`` will implicitly set this to true.
 - **disabled_by_default** (*Optional*, boolean): If true, then this entity should not be added to any client's frontend,
   (usually Home Assistant) without the user manually enabling it (via the Home Assistant UI).
-  Requires Home Assistant 2021.9 or newer. Defaults to ``false``.
+  Defaults to ``false``.
 - **entity_category** (*Optional*, string): The category of the entity.
   See https://developers.home-assistant.io/docs/core/entity/#generic-properties
-  for a list of available options. Requires Home Assistant 2021.11 or newer.
+  for a list of available options.
   Set to ``""`` to remove the default entity category.
 
 MQTT options:

components/cover/template.rst

@@ -62,7 +62,6 @@ Configuration variables:
   of hiding one of them. Defaults to ``false``.
 - **has_position** (*Optional*, boolean): Whether this cover will publish its position as a floating point number.
   By default (``false``), the cover only publishes OPEN/CLOSED position.
-  Parameter useless if you set the POSITION_ACTION (is set to TRUE).
 - **tilt_action** (*Optional*, :ref:`Action <config-action>`): The action that should
   be performed when the remote (like Home Assistant's frontend) requests the cover be set to a specific
   tilt position. The desired tilt is available in the lambda in the ``tilt`` variable.
@@ -71,6 +70,7 @@ Configuration variables:
 - **position_action** (*Optional*, :ref:`Action <config-action>`): The action that should
   be performed when the remote (like Home Assistant's frontend) requests the cover be set to a specific
   position. The desired position is available in the lambda in the ``pos`` variable.
+  Useless if `has_position` is not set to ``true``.
 - **id** (*Optional*, :ref:`config-id`): Manually specify the ID used for code generation.
 - All other options from :ref:`Cover <config-cover>`.
 

components/cover/time_based.rst

@@ -77,7 +77,25 @@ Configuration variables:
     ``esp8266_restore_from_flash: true`` option set. 
     See :doc:`esp8266_restore_from_flash </components/esphome>` for details.
 
+Handle stop_action:
+------------------------
+For some cover controllers, separate switches for UP and DOWN action are used while a stop is issued when sending a counter command.
+This can be handled at the **stop_action** by using the following lambda function:
 
+.. code-block:: yaml
+
+    stop_action: 
+      - lambda: !lambda |-
+          if (id(cover).get_last_operation() == CoverOperation::COVER_OPERATION_OPENING) {
+            // Cover is currently opening
+            id(cover_button_down).press();
+          } else if (id(cover).get_last_operation() == CoverOperation::COVER_OPERATION_CLOSING) {
+            // Cover is currently closing
+            id(cover_button_up).press();
+          }
+
+Be aware that ``get_last_operation`` will only return the last opening or closing operation, but not the last idle operation. 
+This issue is tracked `here <https://github.com/esphome/issues/issues/4252#issuecomment-2132727377>`_.
 
 See Also
 --------

components/cover/tuya.rst

@@ -45,7 +45,7 @@ Configuration variables:
 Supported devices
 -----------------
 
-Tuya cover devices known to be supported by this integration:
+Tuya cover devices known to be supported by this component:
 
 - Tuya ``M515EGWT`` (motor for bead chain roller blinds)
 

components/datetime/index.rst

@@ -42,22 +42,27 @@ Configuration variables:
   a ``name`` will implicitly set this to true.
 - **disabled_by_default** (*Optional*, boolean): If true, then this entity should not be added to any client's frontend,
   (usually Home Assistant) without the user manually enabling it (via the Home Assistant UI).
-  Requires Home Assistant 2021.9 or newer. Defaults to ``false``.
+  Defaults to ``false``.
 - **entity_category** (*Optional*, string): The category of the entity.
   See https://developers.home-assistant.io/docs/core/entity/#generic-properties
-  for a list of available options. Requires Home Assistant 2021.11 or newer.
+  for a list of available options.
   Set to ``""`` to remove the default entity category.
+- **time_id** (**Required**, :ref:`config-id`): The ID of the time entity. Automatically set
+  to the ID of a time component if only a single one is defined.
 
 MQTT Options:
 
 - All other options from :ref:`MQTT Component <config-mqtt-component>`.
 
-Datetime Automation
--------------------
+Time and DateTime Options:
 
-You can access the most recent state as a string of the datetime in :ref:`lambdas <config-lambda>` using
-``id(datetime_id).state``.
-You can also access it as a ``ESPTime`` object by ``id(datetime_id).state_as_time``
+- **on_time** (*Optional*, :ref:`automation`): Automation to run when the current datetime or time matches the current state.
+  Only valid on ``time`` or ``datetime`` types.
+
+Automation
+----------
+
+You can access the most recent state as a ``ESPTime`` object by ``id(datetime_id).state_as_esptime()``
 
 .. _datetime-on_value:
 
@@ -83,6 +88,9 @@ you can get the value as a ESPTime object from the trigger with ``x``.
 
 Configuration variables: See :ref:`Automation <automation>`.
 
+Date Automation
+---------------
+
 .. _datetime-date_set_action:
 
 ``datetime.date.set`` Action
@@ -95,12 +103,12 @@ The ``date`` provided can be in one of 3 formats:
 
     # String date
     - datetime.date.set:
-        id: my_date
+        id: my_datetime_date
         date: "2023-12-04"
 
     # Individual date parts
     - datetime.date.set:
-        id: my_date
+        id: my_datetime_date
         date:
           year: 2023
           month: 12
@@ -108,7 +116,7 @@ The ``date`` provided can be in one of 3 formats:
 
     # Using a lambda
     - datetime.date.set:
-        id: my_date
+        id: my_datetime_date
         date: !lambda |-
           // Return an ESPTime struct
           return {.day_of_month: 4, .month: 12, .year: 2023};
@@ -134,7 +142,7 @@ advanced stuff (see the full API Reference for more info).
   .. code-block:: cpp
 
       // Within lambda, set the date to 2024-02-25
-      auto call = id(my_date).make_call();
+      auto call = id(my_datetime_date).make_call();
       call.set_date("2024-02-25");
       call.perform();
 
@@ -151,12 +159,165 @@ advanced stuff (see the full API Reference for more info).
       // For example, create a custom log message when a value is received:
       ESP_LOGI("main", "Value of my datetime: %04d-%02d-%02d", id(my_date).year, id(my_date).month, id(my_date).day);
 
+Time Automation
+---------------
+
+.. _datetime-time_set_action:
+
+``datetime.time.set`` Action
+****************************
+
+This is an :ref:`Action <config-action>` for setting a datetime time state.
+The ``time`` provided can be in one of 3 formats:
+
+.. code-block:: yaml
+
+    # String time
+    - datetime.time.set:
+        id: my_datetime_time
+        time: "12:34:56"
+
+    # Individual time parts
+    - datetime.time.set:
+        id: my_datetime_time
+        time:
+          hour: 12
+          minute: 34
+          second: 56
+
+    # Using a lambda
+    - datetime.time.set:
+        id: my_datetime_time
+        time: !lambda |-
+          // Return an ESPTime struct
+          return {.second: 56, .minute: 34, .hour: 12};
+
+Configuration variables:
+
+- **id** (**Required**, :ref:`config-id`): The ID of the datetime to set.
+- **time** (**Required**, string, time parts, :ref:`templatable <config-templatable>`):
+  The value to set the datetime to.
+
+
+.. _datetime-time-lambda_calls:
+
+lambda calls
+************
+
+From :ref:`lambdas <config-lambda>`, you can call several methods on all datetimes to do some
+advanced stuff (see the full API Reference for more info).
+
+- ``.make_call()``: Make a call for updating the datetime value.
+
+  .. code-block:: cpp
+
+      // Within lambda, set the time to 12:34:56
+      auto call = id(my_datetime_time).make_call();
+      call.set_time("12:34:56");
+      call.perform();
+
+  Check the API reference for information on the methods that are available for
+  the ``TimeCall`` object.
+
+- ``.hour``: Retrieve the current hour of the ``time``. It will be ``0`` if no value has been set.
+- ``.minute``: Retrieve the current minute of the ``time``. It will be ``0`` if no value has been set.
+- ``.second``: Retrieve the current second of the ``time``. It will be ``0`` if no value has been set.
+- ``.state_as_esptime()``: Retrieve the current value of the datetime as a :apistruct:`ESPTime` object.
+
+  .. code-block:: cpp
+
+      // For example, create a custom log message when a value is received:
+      ESP_LOGI("main", "Value of my datetime: %0d:%02d:%02d", id(my_datetime_time).hour, id(my_datetime_time).minute, id(my_datetime_time).second);
+
+
+DateTime Automation
+-------------------
+
+.. _datetime-datetime_set_action:
+
+``datetime.datetime.set`` Action
+********************************
+
+This is an :ref:`Action <config-action>` for setting a datetime datetime state.
+The ``datetime`` provided can be in one of 3 formats:
+
+.. code-block:: yaml
+
+    # String datetime
+    - datetime.time.set:
+        id: my_datetime
+        datetime: "2024-12-31 12:34:56"
+
+    # Individual datetime parts
+    - datetime.datetime.set:
+        id: my_datetime
+        datetime:
+          year: 2024
+          month: 12
+          day: 31
+          hour: 12
+          minute: 34
+          second: 56
+
+    # Using a lambda
+    - datetime.datetime.set:
+        id: my_datetime
+        datetime: !lambda |-
+          // Return an ESPTime struct
+          return {.second: 56, .minute: 34, .hour: 12, .day_of_month: 31, .month: 12, .year: 2024};
+
+Configuration variables:
+
+- **id** (**Required**, :ref:`config-id`): The ID of the datetime to set.
+- **datetime** (**Required**, string, datetime parts, :ref:`templatable <config-templatable>`):
+  The value to set the datetime to.
+
+
+.. _datetime-datetime-lambda_calls:
+
+Lambda calls
+************
+
+For more complex use cases, several methods are available for use on datetimes from within :ref:`lambdas <config-lambda>`. See the full API Reference for more information.
+
+- ``.make_call()``: Make a call for updating the datetime value.
+
+  .. code-block:: cpp
+
+      // Within lambda, set the datetime to 2024-12-31 12:34:56
+      auto call = id(my_datetime).make_call();
+      call.set_date("2024-12-31 12:34:56");
+      call.perform();
+
+  Check the API reference for information on the methods that are available for
+  the ``DateTimeCall`` object.
+
+- ``.year``: Retrieve the current year of the ``datetime``. It will be ``0`` if no value has been set.
+- ``.month``: Retrieve the current month of the ``datetime``. It will be ``0`` if no value has been set.
+- ``.day``: Retrieve the current day of the ``datetime``. It will be ``0`` if no value has been set.
+- ``.hour``: Retrieve the current hour of the ``datetime``. It will be ``0`` if no value has been set.
+- ``.minute``: Retrieve the current minute of the ``datetime``. It will be ``0`` if no value has been set.
+- ``.second``: Retrieve the current second of the ``datetime``. It will be ``0`` if no value has been set.
+- ``.state_as_esptime()``: Retrieve the current value of the datetime as a :apistruct:`ESPTime` object.
+
+  .. code-block:: cpp
+
+      // For example, create a custom log message when a value is received:
+      ESP_LOGI("main", "Value of my datetime: %04d-%02d-%02d %0d:%02d:%02d",
+               id(my_datetime).year, id(my_datetime).month, id(my_datetime).day,
+               id(my_datetime).hour, id(my_datetime).minute, id(my_datetime).second);
+
+
 See Also
 --------
 
 - :apiref:`DateTimeBase <datetime/datetime_base.h>`
 - :apiref:`DateEntity <datetime/date_entity.h>`
 - :apiref:`DateCall <datetime/date_entity.h>`
+- :apiref:`TimeEntity <datetime/time_entity.h>`
+- :apiref:`TimeCall <datetime/time_entity.h>`
+- :apiref:`DateTimeEntity <datetime/datetime_entity.h>`
+- :apiref:`DateTimeCall <datetime/datetime_entity.h>`
 - :ghedit:`Edit`
 
 .. toctree::

components/datetime/template.rst

@@ -10,20 +10,38 @@ using :ref:`lambdas <config-lambda>`.
 
 .. code-block:: yaml
 
-    # Example configuration entry
     datetime:
+      # Example Date
       - platform: template
-        id: my_date
+        id: my_datetime_date
         type: date
         name: Pick a Date
         optimistic: yes
         initial_value: "2024-01-30"
         restore_value: true
 
+      # Example Time
+      - platform: template
+        id: my_datetime_time
+        type: time
+        name: Pick a Time
+        optimistic: yes
+        initial_value: "12:34:56"
+        restore_value: true
+
+      # Example DateTime
+      - platform: template
+        id: my_datetime
+        type: datetime
+        name: Pick a DateTime
+        optimistic: yes
+        initial_value: "2024-12-31 12:34:56"
+        restore_value: true
+
 Configuration variables:
 ------------------------
 
-- **type** (*Required*, enum): The type of the datetime. Can only be ``date``.
+- **type** (*Required*, enum): The type of the datetime. Can be one of ``date`` or ``time``.
 - **lambda** (*Optional*, :ref:`lambda <config-lambda>`):
   Lambda to be evaluated every update interval to get the current value of the datetime.
 - **set_action** (*Optional*, :ref:`Action <config-action>`): The action that should
@@ -39,6 +57,8 @@ Configuration variables:
 - **initial_value** (*Optional*, string): The value to set the state to on setup if not
   restored with ``restore_value``. Can be one of:
 
+  - For ``type: date``:
+
     - A string in the format ``%Y-%m-%d`` , eg: ``"2023-12-04"``.
     - An object including ``year``, ``month``, ``day``.
 
@@ -49,6 +69,33 @@ Configuration variables:
           month: 12
           day: 4
 
+  - For ``type: time``:
+
+    - A string in the format ``%H:%M:%S`` , eg: ``"12:34:56"``.
+    - An object including ``hour``, ``minute``, ``second``.
+
+    .. code-block:: yaml
+
+        initial_value:
+          hour: 12
+          minute: 34
+          second: 56
+
+  - For ``type: datetime``:
+
+    - A string in the format ``%Y-%m-%d %H:%M:%S`` , eg: ``"2023-12-04 12:34:56"``.
+    - An object including ``year``, ``month``, ``day``, ``hour``, ``minute``, ``second``.
+
+    .. code-block:: yaml
+
+        initial_value:
+          year: 2023
+          month: 12
+          day: 4
+          hour: 12
+          minute: 34
+          second: 56
+
 - All other options from :ref:`Datetime <config-datetime>`.
 
 See Also

components/demo.rst

@@ -1,12 +1,12 @@
-Demo Integration
-================
+Demo Component
+==============
 
 .. seo::
-    :description: Instructions for setting up the demo integration in ESPHome
+    :description: Instructions for setting up the demo component in ESPHome
     :image: description.svg
 
-The ``demo`` integration can be used for testing to generate sample instances of many
-different integrations (sensors, lights, ...)
+The ``demo`` component can be used for testing to generate sample instances of many
+different components (sensors, lights, ...)
 
 .. figure:: images/demo-ui.png
     :align: center
@@ -20,7 +20,7 @@ different integrations (sensors, lights, ...)
 Configuration variables:
 ------------------------
 
-This integration has no configuration variables
+This component has no configuration variables
 
 See Also
 --------

components/dfplayer.rst

@@ -2,7 +2,7 @@ DF-Player mini
 ==============
 
 .. seo::
-    :description: Instructions for setting up DF Player Mini integration in ESPHome.
+    :description: Instructions for setting up DF Player Mini component in ESPHome.
     :image: dfplayer.svg
 
 The ``dfplayer`` (`datasheet <https://wiki.dfrobot.com/DFPlayer_Mini_SKU_DFR0299>`__), component
@@ -14,8 +14,7 @@ allows you to play sound and music stored in an SD card or USB flash drive.
 
     DF-Player mini Module.
 
-For this integration to work you need to have set up a :ref:`UART bus <uart>`
-in your configuration.
+For this component to work you need to have set up a :ref:`UART bus <uart>` in your configuration.
 
 Overview
 --------
@@ -31,16 +30,7 @@ will be required.
 .. code-block:: yaml
 
     # Example configuration entry
-    uart:
-      tx_pin: GPIO2
-      rx_pin: GPIO5
-      baud_rate: 9600
-
-    # Declare DFPlayer mini module
     dfplayer:
-      on_finished_playback:
-        then:
-          logger.log: 'Somebody press play!'
 
 Configuration variables:
 ------------------------
@@ -345,8 +335,8 @@ Sample code
 .. code-block:: yaml
 
     uart:
-      tx_pin: GPIO2
-      rx_pin: GPIO5
+      tx_pin: GPIOXX
+      rx_pin: GPIOXX
       baud_rate: 9600
 
     dfplayer:

components/dfrobot_sen0395.rst

@@ -36,7 +36,7 @@ a :doc:`/components/uart` component (and its requisite GPIO pins) is required in
         name: Mmwave Detected via GPIO
         device_class: motion
         pin:
-          number: REPLACEME
+          number: GPIOXX
           mode: INPUT_PULLDOWN
 
     switch:
@@ -97,7 +97,7 @@ If you don't want/need to change the radar's settings and only need to determine
         name: Presence Detected via GPIO
         device_class: motion
         pin:
-          number: REPLACEME
+          number: GPIOXX
           mode: INPUT_PULLDOWN
 
 .. _dfrobot_sen0395-via_uart:

components/display/addressable_light.rst

@@ -19,18 +19,6 @@ The display requires that an :apiclass:`AddressableLight <light::AddressableLigh
 
 .. code-block:: yaml
 
-    light:
-      - platform: fastled_clockless
-        chipset: WS2812B
-        pin: GPIO4
-        num_leds: 64
-        rgb_order: GRB
-        name: "led_matrix"
-        id: led_matrix_light
-        default_transition_length: 0s
-        color_correct: [50%, 50%, 50%]
-        restore_mode: ALWAYS_ON
-
     display:
       - platform: addressable_light
         id: led_matrix_display

components/display/ili9xxx.rst

@@ -55,8 +55,8 @@ beyond the basic SPI connections, and a reasonable amount of RAM, it is not well
     display:
       - platform: ili9xxx
         model: ili9341
-        dc_pin: 27
-        reset_pin: 33
+        dc_pin: GPIOXX
+        reset_pin: GPIOXX
         lambda: |-
           it.fill(COLOR_BLACK);
           it.print(0, 0, id(my_font), id(my_red), TextAlign::TOP_LEFT, "Hello World!");
@@ -180,13 +180,13 @@ To configure a dimmable backlight:
     # Define a PWM output on the ESP32
     output:
       - platform: ledc
-        pin: 32
-        id: gpio_32_backlight_pwm
+        pin: GPIOXX
+        id: backlight_pwm
 
     # Define a monochromatic, dimmable light for the backlight
     light:
       - platform: monochromatic
-        output: gpio_32_backlight_pwm
+        output: backlight_pwm
         name: "Display Backlight"
         id: back_light
         restore_mode: ALWAYS_ON
@@ -204,8 +204,8 @@ To configure an image adaptive color pallet to show greater than 8 bit color dep
     display:
       - platform: ili9xxx
         model: ili9341
-        dc_pin: 4
-        reset_pin: 22
+        dc_pin: GPIOXX
+        reset_pin: GPIOXX
         rotation: 90
         id: tft_ha
         color_palette: IMAGE_ADAPTIVE
@@ -234,7 +234,7 @@ This config rotates the display into landscape mode using the driver chip.
           mirror_y: true
         color_order: bgr
         data_rate: 80MHz
-        cs_pin: 10
+        cs_pin: GPIOXX
         dc_pin: GPIO13
         reset_pin: GPIO9
 

components/display/index.rst

@@ -2,7 +2,7 @@ Display Component
 =================
 
 .. seo::
-    :description: Instructions for setting up the display integration.
+    :description: Instructions for setting up the display component.
     :image: folder-open.svg
 
 The ``display`` component houses ESPHome's powerful rendering and display
@@ -45,6 +45,9 @@ this behavior by setting ``auto_clear_enabled: false``.
 In the lambda, you can write code like in any :ref:`lambda <config-lambda>` in ESPHome. Display
 lambdas are additionally passed a variable called ``it`` which represents the rendering engine object.
 
+.. figure:: images/display_rendering_line.png
+    :align: center
+
 .. code-block:: yaml
 
     display:
@@ -74,8 +77,10 @@ the rendering engine is always first specify the ``x`` coordinate and then the `
 Basic Shapes
 ------------
 
-Now that you know a bit more about ESPHome's coordinate system, let's draw some basic shapes like lines, rectangles
-and circles:
+Now that you know a bit more about ESPHome's coordinate system, let's draw some basic shapes like lines, rectangles, circles or even polygons:
+
+.. figure:: images/display_rendering_shapes.png
+    :align: center
 
 .. code-block:: yaml
 
@@ -85,27 +90,27 @@ and circles:
         lambda: |-
           // Draw a line from [0,0] to [100,50]
           it.line(0, 0, 100, 50);
-          // Draw the outline of a rectangle with the top left at [50,60], a width of 30 and a height of 42
-          it.rectangle(50, 60, 30, 42);
-          // Draw the same rectangle, but this time filled.
-          it.filled_rectangle(50, 60, 30, 42);
+          // Draw the outline of a rectangle with the top left at [5,20], a width of 30 and a height of 42
+          it.rectangle(5, 20, 30, 42);
+          // Draw the same rectangle a few pixels apart, but this time filled
+          it.filled_rectangle(40, 40, 30, 42);
 
-          // Circles! Let's draw one with the center at [25,25] and a radius of 10
-          it.circle(25, 25, 10);
+          // Circles! Let's draw one with the center at [20,40] and a radius of 10
+          it.circle(20, 40, 10);
           // ... and the same thing filled again
-          it.filled_circle(25, 25, 10);
+          it.filled_circle(20, 75, 10);
 
           // Triangles... Let's draw the outline of a triangle from the [x,y] coordinates of its three points
-          // [25,5], [5,25], [50,50]
-          it.triangle(25, 5, 5, 25, 50, 50);
+          // [25,5], [100,5], [80,25]
+          it.triangle(25, 5, 100, 5, 80, 25);
           // and a filled triangle !
-          it.filled_triangle(125, 5, 105, 25, 150, 50);
+          it.filled_triangle(115, 5, 95, 25, 125, 70);
 
-          // Regular Polygons? Let's draw the outline of a pointy-topped hexagon inscribed in a circle 
-          // centered on [x1=100,y1=100] with a radius of 50
-          it.regular_polygon(100, 100, 50, EDGES_HEXAGON);
-          // and a filled flat-topped octagon!
-          it.filled_regular_polygon(200, 200, 50, EDGES_OCTAGON, VARIATION_FLAT_TOP);
+          // Regular Polygons? Let's draw a filled, pointy-topped hexagon inscribed in a circle
+          // centered on [170,45] with a radius of 20
+          it.filled_regular_polygon(170, 45, 20, EDGES_HEXAGON);
+          // and the outline of flat-topped octagon around it!
+          it.regular_polygon(170, 45, 40, EDGES_OCTAGON, VARIATION_FLAT_TOP);
           // Need to rotate the polygon, or retrieve the coordinates of its vertices? Check the API!
 
 All the above methods can optionally also be called with an argument at the end which specifies in which
@@ -117,33 +122,35 @@ color to draw. For monochrome displays, only ``COLOR_ON`` (the default if color
       - platform: ...
         # ...
         lambda: |-
-          // Turn the whole display on.
+          // Turn the whole display on
           it.fill(COLOR_ON);
-          // Turn the whole display off.
+          // Turn the whole display off
           it.fill(COLOR_OFF);
 
           // Turn a single pixel off at [50,60]
           it.draw_pixel_at(50, 60, COLOR_OFF);
 
-          // Turn off a whole display portion.
-          it.rectangle(50, 50, 30, 42, COLOR_OFF);
-
 For color displays (e.g. TFT displays), you can use the Color class.
 
+.. figure:: images/display_rendering_colors.png
+    :align: center
+
 .. code-block:: yaml
 
     display:
       - platform: ...
         # ...
         lambda: |-
+          auto black = Color(0, 0, 0);
           auto red = Color(255, 0, 0);
           auto green = Color(0, 255, 0);
           auto blue = Color(0, 0, 255);
           auto white = Color(255, 255, 255);
-          it.rectangle(20, 50, 30, 30, white);
-          it.rectangle(25, 55, 30, 30, red);
-          it.rectangle(30, 60, 30, 30, green);
-          it.rectangle(35, 65, 30, 30, blue);
+          it.filled_circle(20, 32, 15, black);
+          it.filled_circle(40, 32, 15, red);
+          it.filled_circle(60, 32, 15, green);
+          it.filled_circle(80, 32, 15, blue);
+          it.filled_circle(100, 32, 15, white);
 
 Additionally, you have access to two helper methods which will fetch the width and height of the display:
 
@@ -156,6 +163,8 @@ Additionally, you have access to two helper methods which will fetch the width a
           // Draw a circle in the middle of the display
           it.filled_circle(it.get_width() / 2, it.get_height() / 2, 20);
 
+          // Turn off bottom half of the screen
+          it.filled_rectangle(0, it.get_height()/2, it.get_width(), it.get_height()/2, COLOR_OFF);
 
 You can view the full API documentation for the rendering engine in the "API Reference" in the See Also section.
 
@@ -218,6 +227,10 @@ In case of fonts rendered at higher bit depths, the background color has to be s
           // Syntax is always: it.print(<x>, <y>, <font>, [color=COLOR_ON], [align], <text>, [color=COLOR_OFF]);
           it.print(0, 0, id(my_font_with_icons), COLOR_ON, TextAlign::CENTER, "Just\U000f05d4here. Already\U000F02D1this.", COLOR_OFF);
 
+
+.. figure:: images/display_rendering_text.png
+    :align: center
+
 .. _display-printf:
 
 Formatted Text
@@ -347,8 +360,7 @@ You can display current time using a time component. Please see the example :ref
 Screen Clipping
 ---------------
 
-Screen clipping is a new set of methods since version 2023.2.0 of esphome. It could be useful when you just want to show
-a part of an image or make sure that what you draw on the screen does not go outside a specific region on the screen.
+Screen clipping can be useful when you just want to show a part of an image or make sure that what you draw on the screen does not go outside a specific region on the screen.
 
 With ``start_clipping(left, top, right, bottom);`` start you the clipping process and when you are done drawing in that region
 you can stop the clipping process with ``end_clipping();`` . You can nest as many ``start_clipping();`` as you want as long
@@ -457,13 +469,8 @@ memory at the time the sensor updates and will be lost when the device reboots.
 
 Examples:
 
-.. figure:: images/graph_screen.png
+.. figure:: images/display_rendering_graph.png
     :align: center
-    :width: 60.0%
-
-.. figure:: images/graph_dualtrace.png
-    :align: center
-    :width: 60.0%
 
 Graph component with options for grids, border and line-types.
 
@@ -602,6 +609,12 @@ To draw the QR-code, call the ``it.qr_code`` function from your render lambda:
               // Draw the QR-code at position [x=50,y=0] with white color and a 2x scale
               it.qr_code(50, 0, id(homepage_qr), Color(255,255,255), 2);
 
+              // Draw the QR-code in the center of the screen with white color and a 2x scale
+              auto size = id(homepage_qr).get_size() * 2; // Multiply by scale
+              auto x = (it.get_width() / 2) - (size / 2);
+              auto y = (it.get_height() / 2) - (size / 2);
+              it.qr_code(x, y, id(homepage_qr), Color(255,255,255), 2);
+
 
 .. _display-image:
 
@@ -921,49 +934,30 @@ Additionally the old page will be given as the variable ``from`` and the new one
 Troubleshooting
 ---------------
 
-Color Test Pattern
-------------------
+Using the Color Test Card
+-------------------------
 
-If you're experiencing issues with your color display, the script below can help you to identify what might be wrong.
-It will show 3 color bars in **RED**, **GREEN** and **BLUE**. To help the graphics display team determine
-the best way to help you, **a picture of the result of this script is very helpful.**
+If you're experiencing issues with your color display, the ``show_test_card: true`` option can help you to identify what might be wrong.
+
+- It will show bars for Red, Green and Blue, graduating to black and white.
+- Together with that it will show the letters "**R**", "**G**" and "**B**" to validate the display geometry.
+- There will be a rectangle around the corners of the display with a marker at the 0,0 corner which should be at the top left of the screen.
+
+.. figure:: images/test_card.jpg
+    :align: center
+    :width: 50.0%
+
+
+
+When all points above are shown correctly then the display is working as expected.
+To help the graphics display team determine the best way to help you, **a picture of the result of this option is very helpful.**
 
 Should you `create an issue <https://github.com/esphome/issues/issues>`__ in GitHub regarding your display, please
-be sure to **include a link to where you purchased it** so that we can validate the configuration you've used.
+be sure to **include a link to where you purchased the display** so that we can validate the configuration you've used.
 
-.. code-block:: yaml
+.. note::
 
-    display:
-      - platform: ...
-        ...
-        lambda: |-
-          int shift_x = (it.get_width()-310)/2;
-          int shift_y = (it.get_height()-256)/2;
-          for(auto i = 0; i<256; i++) {
-            it.horizontal_line(shift_x+  0,i+shift_y,50, my_red.fade_to_white(i));
-            it.horizontal_line(shift_x+ 50,i+shift_y,50, my_red.fade_to_black(i));
-
-            it.horizontal_line(shift_x+105,i+shift_y,50, my_green.fade_to_white(i));
-            it.horizontal_line(shift_x+155,i+shift_y,50, my_green.fade_to_black(i));
-
-            it.horizontal_line(shift_x+210,i+shift_y,50, my_blue.fade_to_white(i));
-            it.horizontal_line(shift_x+260,i+shift_y,50, my_blue.fade_to_black(i));
-          }
-          it.rectangle(shift_x+ 0, 0+shift_y, shift_x+ 310, 256+shift_y, my_yellow);
-
-    color:
-      - id: my_blue
-        blue: 100%
-      - id: my_red
-        red: 100%
-      - id: my_green
-        green: 100%
-      - id: my_white
-        red: 100%
-        blue: 100%
-        green: 100%
-      - id: my_yellow
-        hex: ffff00
+    For displays in 8 bit mode you will see distinct color blocks rather than a smooth gradient.
 
 See Also
 --------

components/display/lcd_display.rst

@@ -2,12 +2,12 @@ Character-Based LCD Display
 ===========================
 
 .. seo::
-    :description: Instructions for setting up character-based HD44780 LCD displays.
+    :description: Instructions for setting up character-based HD44780 LCDs.
     :image: lcd.jpg
 
-The ``lcd_pcf8574`` and ``lcd_gpio`` display components allow you to use HD44780-compatible, character-based LCD displays 
-with ESPHome. This integration is only for LCD displays that display individual characters on a screen 
-(usually 8-40 columns and 2-4 rows), and not for LCD displays that can control each pixel individually.
+The ``lcd_pcf8574`` and ``lcd_gpio`` display components allow you to use HD44780-compatible, character-based LCDs
+with ESPHome. This component is only for LCDs that display individual characters on a screen
+(usually 8-40 columns and 2-4 rows), and not for LCDs that can control each pixel individually.
 
 .. figure:: images/lcd-hello_world.jpg
     :align: center
@@ -90,12 +90,12 @@ faster refresh, especially in conjunction with an :ref:`LCD Menu <lcd_menu>`.
       - platform: lcd_gpio
         dimensions: 20x4
         data_pins:
-          - GPIO32
-          - GPIO33
-          - GPIO5
-          - GPIO17
-        enable_pin: D4
-        rs_pin: D5
+          - GPIOXX
+          - GPIOXX
+          - GPIOXX
+          - GPIOXX
+        enable_pin: GPIOXX
+        rs_pin: GPIOXX
         lambda: |-
           it.print("Hello World!");